ljqTXRX_wifi

智能风扇pwm控制电机转速调速系统毕业设计资料(Intelligent fan pwm control motor speed governor system graduated design information)

COM reference for farPoint Spread 7.0

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)

详细描述了基于ADSP-21262的数字压限器的设计，给出了算法流程，可以根据其描述进行实现(A detailed description of the ADSP-21262 digital limiter based design, flow chart of the algorithm is given, according to the description of implementation)

uCOS+uCGUI例程，主控芯片为STM32，LCD采用FSMC接口连接，实现图形界面的操作(uCOS+uCGUI routines, the main chip for the STM32, the LCD FSMC interface connector, the operation of the graphical interface)

采用4路红外对管进行循迹，电机控制小车运动。(Four infrared channels are used to track the tube, and the motor controls the motion of the car.)

这是一个用51单片机系统仿真ucosii工作的protues电路 本系统包括扩展64k RAM的单片机系统和杨屹移植到51单片机的ucosii 系统 使用方法： 1.安装Protues7.4版，然后用protues打开protues 8051 simulation 文件夹 中的extern ram.DSN 文件 2.打开extern ram.DSN 后，双击单片机在弹出的窗口中的Program File 选项 中选择yy.hex文件。 (yy.hex其实就是yy文件夹中keil文档编译出来的hex文 件，yy文件夹是杨屹的ucos51 系统，用keil 2 可以打开) 3.在Clock Frequency选项中输入22.184M(杨屹的ucos51 用的是22.184M hz的单片机频率) 4.双击VTERM串口调试显示屏，在Baud Rate 选项中选择19200的波特率 5.保存，点击运行就可以看到经典的hello world 了。 (1. Protues7.4 version installed, and then open the protues folder protues 8051 simulation The extern ram.DSN file 2. Open extern ram.DSN, double-click the pop-up window of SCM in the Program File option, select yy.hex file. (yy.hex actually yy folder keil out of the document compiled hex files, yy folder is Yang Yi s ucos51 system, using keil 2 Can open) 3. In the Clock Frequency option to enter 22.184M (Yang Yi of the ucos51 using a microcontroller 22.184M hz frequency) 4. Double-click VTERM serial debug display, in the Baud Rate select 19200 baud rate options 5. Save, click Run you can see the classic hello world)

基于ATmega8 的ucos-II应用(ATmega8' s ucos-II-based applications)

connection的两种连通域方法，上传上去大家应该能看懂的，我从基础学的是能够看得懂，不懂得翻下书(The connection of the two methods of connected domain, uploaded you should be able to understand, I the foundation to learn is to be able to read, not understand through books)

STM32 外部中断程序，用于学习用中断来控制按键(STM32 External Interrupt program)