STM8

STM32F103驱动12864液晶程序，很适合于初学者，希望对你有用(12864 STM32F103 driver program, it is suitable for beginners, I hope useful to you)

用程控放大器MCP6S26对信号进行增益放大，并用显示屏显示出来。(With a programmable gain amplifier MCP6S26 the signal amplification, and displayed by the display.)

单片机的40个实验，这个很全的，是一个很好的东西，希望大家好好使用它。(SCM 40 experiment, this is very full, is a very good thing, hope everyone to use it. )

GPS导航系统 c语言 51单片机开发(in-vehicle GPS navigation system)

可以产生幅度、频率可调的方波，频率50hz到1M(Can produce the amplitude, frequency adjustable Fang Bo, frequency of 50Hz to 1M)

固高运动控制卡源代码，内容详细，对入门运动控制的朋友非常有用。(gugao motion control card system source code, detailed content on the entry of the control of the movement of a friend is very helpful)

本总体方案完成国标GB20600-2006数字电视地面广播传输系统基带部分功能。 输入数据码流经过扰码器（随机化）、前向纠错编码（FEC），然后进行比特流到符号流的星座映射，再进行交织后形成基本数据块，基本数据块与系统信息组合（复用）后并经过帧体数据处理形成帧体，帧体与相应的帧头（PN序列）复接为信号帧（组帧），经过基带后处理转换为输出信号（8MHz带宽内）。该信号经变频转换为射频信号（UHF和VHF频段范围内）。用C程序设计了图形交互界面，可以在界面上直接设置调制参数。(The overall program completion GB GB20600-2006 digital terrestrial television broadcasting transmission systems baseband function. The input data stream through the scrambler (randomization), forward error correction (the FEC), then the symbol constellation mapping bitstream to the stream, and then after forming the basic block interleaving, the basic data block and information combined system ( multiplexing) after data processing and after the frame body forms a frame body, frame body with a corresponding header (PN sequence) multiplexed signal frame (framing), after post-processing baseband signal is converted to an output (internal 8MHz bandwidth). The signal is downconverted to a radio frequency signal (in the VHF and UHF frequency range). C program designed graphical interface, you can set modulation parameters directly on the screen.)

在淘宝上购买的毕业论文，价值400的源程序，包含全部文件。一款基于单片机的灭火机器人模型的设计。系统以STC89C52RC单片机为控制核心，创新自制了火焰传感器用来测量火源，使用TCRT5000型光电对管检测循迹黑线，L298驱动电机前后转动，LCD1602液晶显示灭火的次数，通过控制继电器开关风扇灭火。(On Taobao buy thesis, the value of the 400 source code, including all documents. Fire fighting robot model based on a single-chip design. System microcontroller STC89C52RC to control core, innovation homemade flame sensor is used to measure the fire source, tracking black line on the tube use TCRT5000 photoelectric detection, L298 drive motor rotating back and forth, the LCD1602 LCD number of fire-fighting, fire control relay switch fan .)

CC430定时器应用程序定时2MS点亮LED灯，定时2MSLED灭。(CC430 timer application timing the 2MS light LED lights, timing 2MSLED off.)

串口通信传输与接收。既：发送一个字节到MCU,再由MCU发回来。(Serial communication transmission and reception. Bothto send a byte to the MCU, and then sent back by the MCU.)