Sender

大整数阶乘新思路，实现了大整数阶乘的程序(Large integer factorial new ideas, the realization of a large integer factorial process)

奥斯电子zigbee无线传输点亮LED灯的源代码(zigbee wireless lighting source)

基于单片机的函数信号发生器的C语言代码，自己做的(Function signal generator based on single chip microcomputer C language code )

本系统以单片机AT89C52为核心,以数模转换器DAC0832实现方波、正弦波、三角波、锯齿波波形的输出，实现信号发生器的简易功能。(This system with single chip microcomputer AT89C52 as the core, with digital to analog converter DAC0832 achieve square wave, sine wave, triangle wave, sawtooth wave form output, realize the simple function of the signal generator.)

DS1302+89c51的例程代码，实测可用(DS1302 STM32)

STM32 4路AD+5110显示 ( )

步进电机驱动，四相五线步进电机控制的测试程序，C51编写，读者可稍加修给即可应用(Stepper motor driver)

TCS3200传感器捕获方波频率，可以根据频率变化识别外部光源颜色(TCS3200 sensor to capture a square wave frequency, the frequency change can identify the external light source color)

基于单片机的电阻测量系统，带vb上位机控制和显示同时还有无线发射(MCU-based resistance measurement system with vb PC control and display as well as a wireless transmitter)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)