Marquee plus delay a routine procedure. . . . . . . . . . . . . . . . .

一些单片机的51实例，仅供参考-some of the 51 examples for reference purposes only.

4X4键盘扫描源程序 适用于基于Keil80C51 -4X4 Mirror扫captured Tai-ying, the most序适using quilt prices quilt Keil80C51

lcd测试程序，C51的-LCD testing procedures C51

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

通过环路串口判断串行通信电平转换芯片功能是否正常，并通过读写DRAM 判断硬件。-Through the loop to determine serial communication serial port level translator chip features and whether it is normal, and through reading and writing DRAM hardware judge.

CC2430 基础实验一LED灯自动闪烁-CC2430 experimental basis for a flashing LED light automatically

--- -initial--- - MOVLA 00H IODIR PA IODIR PB IODIR PC MOVAM PA MOVAM BSR MOVAM STATUS MOVAM TMR0 MOVAM TMR1 MOVAM TMR2 -------end initial----- -------------乘法运算------------ 乘数->10H 被乘数->11h 结果(积)->12H 14H 15H 16H 17H(中间运算) --------------------------------- MOVLA 05H 乘数 ------------ MOVLA 00H IODI R PA IODIR PB IODIR PC MOVAM PA MOVAM BSR MOVAM STA TUS MOVAM TMR0 MOVAM TMR1 MOVAM TMR2------- end initial multiplication------------------------------ multiplier-

pic单片机程序,用于数制转换,可将16位二进制数转换成5位十进制数.-pic microcontroller procedures for a number of system conversion, 16 can be converted into binary-decimal number five.

本程序可以利用74164串入并出芯片在七段共阴数码管上依次点亮0至9十个数字.. PA0....数据 PA1.....CP PA2.....是位选 在ATMEGA644P上调试通过-This procedure can be used to string 74,164 and a total of a chip in the seventh followed by vaginal digital tube light figures 0-9 10 .. PA0 .... data PA1 ..... CP PA2 ..... is selected through ATMEGA644P debugging

无线传感网络结点数据采集，应用CC2420和Atmel的Atmega128L进行开发，环境为ICCAVR-Wireless sensor network node data collection, application CC2420, and Atmel" s Atmega128L for development on the environment, ICCAVR