在32019T(SED1335驱动)上显示BMP图象，假设图象数据已固化在FlashROM中。

keil编译,单片机资料,Can通讯。-keil compiler, microcontroller information, Can communications.

51单片机开发的双路冷气机自动切换报警控制器-51 MCU development of dual air-conditioning automatically switch alarm controller

本文件是单片机开发板STK500的使用说明，与大家共享-The present document is a single chip using the STK500 development board that share

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

温度传感器用单总线DS18B20，CPU为2051，三个按键，分别为UP，DOWN，SET温度调节上限为125度，下限为-55度。-Single-bus temperature sensor DS18B20, CPU for 2051, three buttons, namely, UP, DOWN, SET temperature regulation maximum of 125 degrees,-55 degrees for the lower limit.

keilc51 startup代码解释 -keil c51 startup source code explain

点亮LED灯，C语言编写，可以在keil下运行。实现第一个小灯的不停闪烁，初学着可以好好参考。-LED lights lit, C language, you can run keil. Achieve the first of a small non-stop flashing lights, can make reference to the beginner.

S3C44B0X 是常用的一款基于ARM7TDMI 内核的RISC 处理器，这是它的LCD公测程序-S3C44B0X is one of the commonly used kernel based on the ARM7TDMI RISC processor, This is its LCD Gongce procedures

开发硬件电路需要用到液晶显示模块1602的用户必备。调试实验源程序第二部分。-Hardware needed to develop liquid crystal display module 1602 required the user. The second part of the experimental source code debugging.

本程序是基于FM1702的射频卡读写器的单片机控制的C语言程序，所用单片机为AT89C52.-This procedure is based on the FM1702 RF card reader control of single-chip C-language program, using single-chip microcomputer for the AT89C52.