used PDIUSBD12 development of the USB bus with 429 data conversion MCU firmware

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

单片机atmega16内部模数转换程序，功能：通过调节ADC0、ADC1两个电位器来改变输入电压，并在数码管同时显示两路电压值。-SCM atmega16 internal analog-digital conversion procedure, function: by adjusting the ADC0, ADC1 two potentiometers to change the input voltage, and also showed two-way digital control voltage value.

宏芯 t103程序 能解码VGA CVBS S_VIDEO的视频解码，程序的开发环境是stc89c58rd+ 在keil c下已经编译通过-T103 Terawins procedures can decode VGA CVBS S_VIDEO video decoder, the program development environment is stc89c58rd+ In keil c have been compiled through

这是关于Proteus仿真的源程序，用于ARM7，编译环境为ADS-This is the source on the Proteus simulation for the ARM7, the compiler environment for ADS

实验学习型电子钟包括红外线控制密码da控制led亮度ad转换语音转换闹铃-Experimental study electronic bell, including infra-red control password da control led brightness ad-speech converter alarm

自己的51开发板源代码B，里面包含有LCD1602实验，lcd12864实验，ps2 lcd1602，串口通讯，红外遥控，计算器，继电器控制，矩阵键盘等实验程序，内容丰富-51 development board

基于单片机的电动机的正反转电路 机构简单，介绍详细-Based on single-chip motor body positive circuit is simple, to introduce a detailed

液晶显示模块1604测试源码。显示数字，使用汇编语言编写。-LCD Module 1604 test source. Figures show that is written in assembly language.

用增强型单片机51RD2做的控制器，功能包括驱动320*620的LCD，AD/DA采集，键盘采集，微型打印机接口，多CPU通信，ISP在线远程下载等。-with enhanced microcontroller 51RD2 do controller, Driver features include 320* 620 LCD, AD/DA acquisition, keyboard acquisition, micro-printer interface, Multi-CPU communications, remote ISP online downloads.

读取mifareOne卡的数据，并显示在LCD模块上，采用C语言开发，开发编译调试环境KeilC。基于RC522模块。-Read data from mifare one card and display it in LCD module.