中国广州周立功单片机移植的ucosII 很实用

非接触式IC卡设计编程的样例-non-contact IC card design Programming Example

常用串行EEPROM的编程应用，EEPROM是"Electrically Erasable Programmable Read-only"（电可擦写可编程只读存储器）的缩写，EEPROM在正常情况下和EPROM一样，可以在掉电的情况下保存数据，所不同的是它可以在特定引脚上施加特定电压或使用特定的总线擦写命令就可以在在线的情况下方便完成数据的擦除和写入-Commonly used application of serial EEPROM programming, EEPROM is Electrically Erasable Programmable Read-only (Xinhua EPROM) acronym, EEPROM under normal circumstances and EPROM, as in the case of power-down to save data , What is different is that it can exert in a particular pin on a specific voltage or use specific bus write command can be in the case of online data to facilitate the completion of the erase and write

详细介绍了单片机的总线设计法，讲述清除并有设计实例-Details of the MCU bus design method, and a design example about the removal

一款关于ISD4004语音芯片的开发实例，采用C语言编写，具有完整的 SPI 总线操作函数，一定会为你做ISD4000系列芯片的开发带来很大帮助-ISD4004 voice chip on a development instance, using C language, with a complete function of SPI bus operations, will definitely help you make ISD4000 series chips have a great help

mega8数码管电子钟程序，用32768晶振，很准确。-mega8 electronic clock.

此代码是我们在单片机来控制CPLD记数,然后读出并转换数据,精度很高,在我们学校的电子设计大赛上还获的了二等奖-this code is in MCU to control CPLD counting, and then read out the conversion of data, the accuracy is high, In our schools Electronic Design Competition was also a second prize of

cc2430内外围设备的基本应用程序，目录如下： CC2430-1 自动闪烁 CC2430-2 按键控制开关 CC2430-3 按键控制闪烁 CC2430-4 T1的使用 CC2430-5 T2的使用 CC2430-6 T3的使用 CC2430-7 T4的使用 CC2430-8 定时器中断 CC2430-9 外部中断 CC2430-10 片内温度 CC2430-11 1/3AVDD CC2430-12 AVDD CC2430-13 单片机串口发数 CC2430-14 在PC用串口控制LED CC2430-15 在PC用串口收数并发数 CC2430-16 串口时钟PC显示 CC2430-17 系统睡眠工作状态 CC2430-18 系统唤醒 CC2430-19 睡眠定时器的使用 CC2430-20 看门狗模式 CC2430-21 喂狗 CC2430-22 定时唤醒 CC2430-23 PWM控制小灯亮度-RF CC2430

英飞凌C166之XC164CS开关SWITCH程序-Infineon C166 procedures of XC164CS switch SWITCH

内置T6963C的液晶图形模块的详细资料-Built-T6963C Graphic LCD Module details

此程序为飞思卡尔智能车校内选拔赛主控为STC51单片机的初始程序-This is a smart car in schools Freescale trials STC51 SCM control for the initial procedure