SPI接口型E2PROM内部存储器的组织及读.写控制方法.

BH1415F调频台控制C程序。使用AT89C52单片机，12MHZ晶振，用共阳四位LED数码管。频率数据转换为显示用BCD码函数。-C FM BH1415F control procedures. AT89C52 single-chip microcomputer use, 12MHZ crystal, with a total of four LED digital tube Yang. Frequency data into a display function using BCD code.

这是msp430系列单片机的封装库，protel99se library，挺有用的哟。-This is the Controller Series MCU package libraries, protel99se library, quite the yo.

汇编语言写的电子强答程序,对学生学习单片机很有帮助-assembly language to write electronic-A process that the students learn helpful MCU

周立功I2C源代码,用于AT24C02,可以借鉴学习下-Week Ligong I2C source code for the AT24C02, can learn from studying under the

完全正确的频率计供大家参考（1602显示),非常适合单片机学习和使用-Completely correct frequency for your reference (1602 show), very suitable for the learning and use of single-chip microcomputer

用于排队叫号系统的中央显示大屏控制程序。可以循环滚动显示文字，最大5层。-Call queuing system for its large central display screen control procedures. Could be re-rolling display text, the largest 5 layer.

本文介绍了液晶显示模块LCM12832ZK与飞利浦80C552单片机的接口应用-This paper introduces the liquid crystal display module LCM12832ZK with Philips 80C552 MCU Application

详细介绍了以太网收发器RTL8019芯片，中文文档，免除了读英文文档的痛苦和低效-Described in detail RTL8019 Ethernet transceiver chip, Chinese documents, eliminating the pain of reading the document in English and inefficient

基于AT89C52单片机的电热水器设计，包括原理图和程序-Electric water heater based on AT89C52 microcontroller design, including schematic and procedures

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.