16单片机AD转换一般有连续转换和中断转换两种，本程序采用中断的方法实现AD 转换...

铁电存储器FM25CL64 的C51 编程。-Ferroelectric RAM FM25CL64 the C51 programming.

该文件提供51c程序点阵led显示模块，可以运行在arm平台-51C of the document provides procedures led dot matrix display module can be run on arm platform

汽车行驶记录仪的数据初始化组件，主要通过RS232串口或者USB口写数据到单片机，详细协议及数据格式参见国标的相关文件，该系统已经通过的国家公安部的标准检测-Vehicle Data Recorder initialization components, primarily through the RS232 serial or USB port to write data to the microcontroller, detailed agreement and data format See National Standard document, which has been adopted by the Ministry of National Standard Test

全速运行程序，可看到串口调试助手的接收区显示“41 42 43 44 45 46 47 48”。手动发送“0102030405060708091011”，打开WATCH窗口可看到50H~5AH地址单元的值为“0102030405060708091011”，请注意50H单元是串口接收数据起始存放地址，70H单元是串口接收数据结束存放地址。-Run the program at full speed, can see the serial debug assistants reception area shows

64点阵C程序有移动功能具有时间显示，可设置时间，断电保存-64 dot-matrix C procedures with mobile features the time display can be set-up times, power save

摩托罗拉单片机延时程序举例，无密码，解压即可使用--Programming examples for time delay in Motorola s SCM.

MSP430系列单片机的I2C源程序。可用于对I2C的学习和研究-MSP430 series MCU I2C source. I2C can be used to study and research

用单片机的C语言实现的开机时间显示上次关机时间（存在看门狗里），还有显示当前时间。可供单片机程序开发人员参考。-MCU C language shows the uptime shutdown last time (there watchdog Lane), and show the current time. SCM procedures for the development of reference.

本程序主要通过外部中断INT0及3.3端口读取PS2键盘值并通过LCD1602显示，键扫描码的解码通过数组方式解码，程序的解码功能主要针对数字及大小写字母和常用标点符号 硬件描述：PS2键盘的时钟线（clk）接89S51的INT0（P3.2）,数据线data接（P3.3） LCD的控制端口分别为： RS = P2^7，RW = P2^6，EP = P2^5，数据端口为P0，液晶显示偏压VL必须接 -This procedure mainly through external interrupt INT0 and 3.3 read PS2 keyboard port value through LCD1602 display, key scan code decoder way through an array of decoding, the procedure for decoding function of the major figures and upper and lower case letters and punctuation marks commonly used hardware description: PS2 keyboard clock line (clk) then 89S51 the INT0 (P3.2), data lines data access (P3.3) LCD control port, respectively: RS = P2 ^ 7, RW = P2 ^ 6, EP = P2 ^ 5, data ports for the P0, LCD bias VL must be received

读写am29F040的C语言程序，适用多种型号的FLASH-Am29F040 the C language to read and write procedures for a variety of models of FLASH