用loop51实现的可调式脉冲发生及检测器，可以手动输入所发生脉冲的频率和占空比，实时检测及动态显示...

监视室内温度并获取温度，当温度到达60摄氏度以上即发出警报 -Monitor the indoor temperature and obtain the temperature, when the temperature reaches above 60 degrees Celsius that the alarm

uIP运行于8位-16位单片机上TCPIP协议源码0.9　　我自己做过的　很好的　希望与大家爱好者分享-Application of ulP runs on eight 16-bit microcontroller agreement on the source of 0.9 TCPIP I done good and we hope to share lovers

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

192*64显示lcd程序，功能：根据参数x_add,y_add往LCD中写1个字 输入：1： 写到LCD的X、Y坐标；2：数据地址 输出：无-LCD display procedures, functions : the parameters x_add, LCD y_add to write a character input : 1 : LCD wrote the X, Y coordinates; 2 : data output address : None

c51语言入门教程.适合于初学者使用,通俗易懂-C51 Language Tutorial. suitable for beginners to use, easy to understand

该程序为LED大型显示屏驱动程序，全部源代码为C语言编写-The program for the large LED display drivers, all the source code for the C language

< AVR单片机C语言开发入门指导>> Project 多通道AD转换 Chip type ATmega8 Clock frequency :内部RC（INT）8.000000M Author ATMEGA8内部的转换器-" > Project multi-channel AD converter Chip type ATmega8 Clock frequency: the internal RC (INT) 8.000000M Author ATMEGA8 inside the converter

一个非常好的单片机读写液晶的程序，已经服了源码。-A very good single-chip LCD to read and write procedures, had already served a source.

电机调速是单片机或DSP硬件平台结合电机运行机制设计相应算法，并以软件实现-Motor speed is a microcontroller or DSP hardware platforms, operating mechanism with electrical design corresponding algorithms, and to software implementation

240128的液晶显示调试程序，供c51开发使用-240,128 LCD debugger, for the development of the use of c51