智能车XS128芯片 LED测试程序.仅供参考

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

拼音输入法 用于C51的编程 希望大家喜欢-Pinyin input method for C51 programming hope everyone likes

可以直接将图片转化为lcd 的源代码，很方便你的使用。-Can be directly translated into lcd picture of the source code, very easy to use you.

MSP430系列单片机串口编程详细介绍，有实用的编例子和注释，很好的学习资料-MSP430 series microcontroller serial programming detailed description of the compilation of practical examples and notes, a very good learning materials

基于TI的MSP430的方面的相关的软件和MSP430的相关的资料.-based on TI"s MSP430 aspects of the software and MSP430 relevant information.

philips单片机IAP读的源代码，使用c来调用-philips Singlechip IAP Reading the source code, use c to call

MAX1247子程序,实现12位高精度串行AD转换-MAX1247 subroutine, 12 realize high-precision serial AD converter

ADC0809是广泛使用的模／数转换器，在可不采用外部总线结构的单片机系统中(如 由AT89C51组成的系统)。ASC0809的数据线直接与单片结构的I／0 口相连，并由单片机的I／O 口直接对ADC0809进行控制。-ADC0809 is widely used in analog/digital converters, in not using the external bus architecture in the single-chip microcomputer system (such as the composition of the system by the AT89C51). ASC0809 data lines directly with the monolithic structure of I/0 I connected the MCU I/O port directly to control the ADC0809.

广东工业大学第五届电子设计大赛 《交通灯控制系统》 信息工程学院 04应用电子2班 -Guangdong University of the fifth Electronic Design Contest

使用IA4421无线射频芯片传输数据，发送端通过串口每次发送多字节，接收端将接收到的数据显示在上位机上。-IA4421 chip using radio-frequency transmission of data through the serial port for each sender to send multi-byte, the receiver will receive the data displayed in the upper machine.