用C51编写的现场总线多机通讯程序，这个程序调试通过，现在应用在微机数据采集系统中。...

基于51系列单片机的串口通信测试程序，希望对大家有帮助-Based on 51 Series Single-chip serial communications test program, and they hope to have everyone help

AVR GCC编程参考手册，非常适合做开发参考-AVR GCC programming reference manual, is well suited to do the development of reference

SH7144芯片使用实例 请使用Hew4进行调试-SH7144 chip using examples use the debug Hew4

在PIC上实现CRC16算法的源程序，可用于一般通讯中的校验。-PIC in achieving CYXLIC REDUNDANCY source algorithm can be used in the general communications check.

PID是控制智能小车的经典算法在过程控制中，按偏差的比例（P）、积分（I）和微分（D）进行控制的PID控制器（亦称PID调节器）是应用最为广泛的一种自动控制器。它具有原理简单，易于实现，适用面广，控制参数相互独立，参数的选定比较简单等优点；而且在理论上可以证明，对于过程控制的典型对象──“一阶滞后＋纯滞后”与“二阶滞后＋纯滞后”的控制对象，PID控制器是一种最优控制-PID control of the smart car is the classic algorithm in process control, according to the percentage of deviation (P), Integral (I) and differential (D) control of PID controller (also known as PID regulators) is the most widely used as a automatic controller. It has simple, easy to realize, the application of a wide range of control parameters are independent of each other, the selection of relatively simple parameters, etc. and in theory can be proved that for a typical process control objects ─ ─

tmer_a,TI TMPS430单片机使用例子，希望对象我一样的初学者有帮助-tmer_a, TI MCU TMPS430 use examples, I hope that the same object is to help beginners

MSP430F247 Program Example-MSP430F247 application

本文介绍了AT89C2051单片机的性能和特点，并在分析了超声波测距原理的基本系统框图。该设计系统经校正后，其测量精度可达0.1米-This paper introduces the AT89C2051 performance and features, and the analysis of the ultrasonic distance measurement principle diagram of the basic system. The design of the system calibration, measurement accuracy of 0.1 meters

红外线遥控器按键检测程序. 通过检测两次下降沿之间的时间差判断接受到的数据位. 已经通过了测试,能够正确区分出32bit数据的遥控器按键键值. 具有数据重发功能,但是数据的重发有点频繁. 使用晶震频率为11.0592MHz,所有定时值都是基于这个频率计算. 占用很少量的CPU时间,使用了外部中断0接受数据,定时器0进行计数, 定时器1作为串口的波特率发生器(Band = 9600).-Infra-red remote control button detection program. By detecting falling edge twice to determine the time difference between the received data bit. Has passed the test, could correctly distinguish 32bit data button remote control key. With data re-issued, but data a bit of re-issued frequent. Zhenyuan frequency of use of crystal 11.0592MHz, all timing values are calculated based on this frequency. occupied by small quantities of CPU time, use the external interrupt 0 to accept data, timer 0 to count, timer 1 as a string port baud rate generator (Band = 9600).

凌阳16位单片机的启动代码，它是源码，是凌阳的公司提供的-Sunplus 16-bit single-chip start-up code, it is the source code is provided by the company of Sunplus