脉冲测速代码。在51单片机上使用。可用于电动机。

直流电机反转控制程序,使用L298N,C语言编写-DC motor control program

以

自动交通管理系统 用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁止线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示） 同时用2位数码管进行30秒钟递减时间显示。-automatic traffic management system using red, green, yellow a total of three light-emitting diodes, said two traffic lights, using SCM time simulation shows the regular traffic signal control. Signal changes in the law to be as follows : 1) Release Line : green clearance 25 seconds, bright yellow warning five seconds, and then the red-ban. 2) prohibit the lines : red-Ban 30 seconds, then green clearance. 3) When the red light in one direction- that if the direction of a car passed, the use of loudspeakers sound alarm. (Red light signals can hit 3- 5V analog said), while using two digital tube for 30 seconds decreasing time displayed.

这是单片机C语言位操作函数！给大家参考使用，可以直接在单片机中引用，不需要自己去编写，弥补了C语言位操作没有汇编灵活的缺点-This is the C language SCM- manipulation functions. For your reference use, can be directly invoked in SCM, you do not need to do to prepare. compensate for the C-language compilation flexible operation without the shortcomings

protues 仿真的c51单片机走马灯程序,里面包含keil代码,可以与protues共同联机调试.-C51 single-chip simulation protues lantern procedure, which contains keil code, can be shared online debugging protues.

MSP430 CRC算法的实现 （基于msp430x16x）-MSP430 CRC algorithm (based on msp430x16x)

ICCAVR下的RTOS2系统-ICCAVR system under the RTOS2

编译环境：ICC AVR 6.31A 单片机：AT90S8515 PC.0出音乐信号，INT0，INT1分别接下一首、播放/暂停键 开机处于暂停状态，按下播放/暂停键开始放音，自动播放完8首，会再进入暂停状态。 所有的暂停状态都采用掉电模式。 -build environment : ICC AVR microcontroller 6.31A : AT90S8515 PC.0 musical signal INT0, INT1 respectively took one, Play/Zantingjian Boot suspended, press Play/Zantingjian start of audio, automatic broadcast End 8, will enter the state. All the suspended power-down mode is used.

开发环境为：iarEWARM5.20 语言为c语言 2378的启动文件，为EWARM5.20 例程中的文件 利用lpc2378的io口控制ocmj12232c-1液晶的程序。程序有详尽接口说明和完整的注释。ocmj12232c-1是st7920控制的显示模块。使用lpc2378移植的程序这是第一个。-Xi Yuan-kai为alas iarEWARM5.20 To:为c Pang Pang Sheng Sheng-hung 启 cavity 2378 ， glass text为bird

注:protel电路图 1.INPUT12为高压气压和低压压传感器输入端. 2.OUTPUT为充气输出控制端. 3.当高低压有接地信号时,电机正转,气阀打开. 4.INPUT2低气压时有信号时,充气OUTPUT输出,充气电机转. 5.RS1与RS2是调节阀门距离用地 6.RS3是与气阀电机同步时,是气阀电机的转动圈数传感器. 7.RS4是调节延时时间用地-Note: protel circuit 1.INPUT12 and low-voltage high-pressure pneumatic pressure sensor input. 2.OUTPUT output control for the inflated side. 3. When the high and low pressure have a grounding signal when the motor is transferred, the valve opens. 4.INPUT2 low pressure when there is signal output OUTPUT inflatable, inflatable motor switch. 5.RS1 and RS2 is the regulator valve from the land 6.RS3 synchronous motor with the valve, the valve motor is rotating circle the number of sensors. 7.RS4 delay time to regulate land