cdcemu

智能车开发串口接收数据上位机软件.源代码.如果自己加上数据分析功能,就非常有用.(Development of intelligent vehicle PC software serial receive data. The source code. If they combined data analysis, it is very useful.)

对STM8L151各个功能模块测试程序,十分方便初学STM8L151各个功能有IO中断,中断唤醒,定时中断,串口接收发送,AD转换程序,SLEEP模式(STM8L151 each function module test program, very convenient beginners STM8L151 each function is IO interruption, interrupt, timer interrupt, serial port receive send, AD converter, the SLEEP mode)

nrf2401M16无线模块开发案例，很实用哦(nrf2401 wireless module development case)

crc校验的一种计算方式，可以用于网络协议或串口、can协议的校验位计算，有封装好的函数(A calculation crc check can be used for network protocols or serial port, can protocol parity bit calculation, there is a good function package)

基于单片机STC89C51和74LS164的多功能数字万用表(Based on microcontroller STC89C51 and 74 ls164 multi-function digital multimeter)

基于430的DC_DC变化，采用PID控制，调节PWM的输出占公比，从而反馈调节输出电压(Based on 430 DC_DC change, using PID control, adjust the PWM output accounted common ratio, thus regulating the output voltage feedback)

BlueCore4 Datasheet BC417143 ·APF有源滤波控制器程序，因为改代码 ·利用51单片机实现DS1302的驱动，以C ·利用STM8L实现诺基亚5110液晶的驱动 ·盛群单片机指令集:简体中文，PDF格 ·SHT11 程序，I2C总线方式。写I2C时 ·7寸彩屏 STM32的固件库3.5 FSMC驱动 ·一种伺服电机的PID控制算法，可以完 ·基于Atmega16单片机的机器人行走、 ·51单片机驱动2.6英寸触摸液晶屏幕， ·stm32 pwm 固件库 大连理工大学 信 ·无线传感网络基础 wireless sensor ·LPC11u14芯片的系统时钟驱动

仿真电话键盘拨号的电路图 C 以及HEX文件 是我的单片机考试作业(this is my master piece)

xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1－启动与停止步进电机运行 K2－设定步进电机运行圈数 （1-20圈） K3－设定步进电机转动方向 K4－设定步进电机运行速度 步进电机的转速控制分16档，数字越小，转速越快。 7.5度步进电机；周期7.5×4=30度，电机转动一圈需12个周期 资源：p1.0-p1.3接反向器74ls14，输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口按键：lcd1602插入实验仪(xl Series Singlechip Experiment LCD1602 demo program shows the direction of stepper motor speed controller circle shows the number of adjustable LCD1602 direction stepper motor controller lap speed of a few adjustable K1-start and stop the stepper motor running K2-setting step motor running a few laps (1-20 laps) K3-set stepper motor rotation direction of K4-setting speed of stepper motor stepper motor speed control minutes 16 stalls, the number of smaller, faster the speed. 7.5 degree stepper motor cycle of 7.5 × 4 = 30 degrees, rotating electric lap 12 cycles required resources: p1.0-p1.3 then reverse browser 74ls14, followed by stepper motor output p3.7 then provide a small speaker key tone, p1.4-p1.7 port access keys: lcd1602 insert Tester)

无线通讯nrf905，很适合初学者来学习，里边包括了对射频寄存器的设置什么的(Wireless communication nrf905, it is suitable for beginners to learn, inside contains the settings for RF registers what)