stm32f407 手写识别

深圳固高科技的运动控制卡设置软件源代码,C++ 编写,目前正在现场使用(Googol control card)

电力系统电度表通讯协议，主要针对DL645协议标准(Power system meter communication protocol, mainly for DL645 protocol standards)

智能车的智能车的设计全过程，对于初学者很有帮助，有助于参加比赛的同学设计全过程，对于初学者很有帮助,(Smart car Smart car design the whole process of useful for beginners, students who participate in the competition designed to help the whole process of useful for beginners,)

这是基于单片机的计算器程序，可以实现加减乘除的功能(This is based on single-chip calculator program, Math functions can be achieved)

说明：  双路输出控制器”具有信号输出时间设定、 输出信号占空比调整、 当前输出通道及时 间显示、系统工作参数存储、串口通讯及 LED 指示等功能。 “双路输出控制器”通过串口完 成信号输出时间设定功能；通过 EEPROM 完成系统工作参数存储功能；通过按键完成输出通 道切换、 输出信号占空比调整及停止信号输出功能； 系统硬件电路主要由 MCU 控制单元、独 立按键、 LCD 显示单元、 串口通讯单元、 EEPROM 数据存储单元和 LED 指示单元组成(Dual output controller has the signal output time setting, adjust the duty cycle of the output signal, the current output channel in time Between display, system operating parameters are stored, serial communications and LED indicator. Dual Output Controller through serial END A signal output time setting function complete system operating parameters via EEPROM memory function complete output pass through the key Channel switching, adjust the duty cycle of the output signal and the stop signal output function the system hardware circuit is mainly controlled by the MCU unit, alone Li buttons, LCD display unit, serial communication unit, EEPROM data storage unit and LED indication units)

利尔达 MSP430F5438学习板全套资料(LSD the MSP430F5438 learning board full set of information)

ME850单片机开发实验仪演示程序 - LCD1602显示 基于 c51系列的单片机程序，用AT89S52延时通过(ME850 SCM experimental instrument demo- LCD1602 display based on c51 series SCM process, using AT89S52 delay through)

基于430的DC_DC变化，采用PID控制，调节PWM的输出占公比，从而反馈调节输出电压(Based on 430 DC_DC change, using PID control, adjust the PWM output accounted common ratio, thus regulating the output voltage feedback)

C++电梯模拟程序，同过仿真的方式在控制台下测试其电梯程序的准确性(elevator simulation)

交流电动机的矢量控制（Transvector Contrl）理论，从理论上解决了交流电动机转矩的高性能控制问题。其基本思想是在普通的三相交流电动机上设法模拟直流电动机转矩控制的规律，在磁场定向坐标上，将电流矢量分解成产生磁通的励磁电流分量 和产生转矩的转矩电流分量 ，并使两分量互相垂直，彼此独立，然后分别进行调节。这样，交流电动机的转矩控制，从原理和特性上就与直流电动机相似了。因此，矢量控制的关键仍是对电流矢量的幅值和空间位置的控制。(AC motor vector control (Transvector Contrl) theory, control theory to solve the problem of high-performance AC motor torque. The basic idea is to try to simulate the DC motor torque control law in the ordinary three-phase AC electric motor in field-oriented coordinates, the current vector decomposed to produce the excitation current component of the magnetic flux generating a torque current component and torque, and two components perpendicular to each other, independently of each other, and then were adjusted. Thus, AC motor torque control, the principle and characteristics of the DC motor on and similar. Therefore, the key vector control is still the amplitude and spatial position of the current vector control.)