ty

单片机音频通信9170和9200，接收发送源程序(9170 and 9200 microcontroller audio communication, the receiver sends source)

Seekers导引头模型仿真C++源码；内含Seeker仿真模块、导引头电机环节、导引头PID环节等。(Seekers seeker model simulation C++ source containing Seeker simulation module, motor aspects seeker seeker PID link and so on.)

飞思卡尔单片机xs128AD模数转换代码(Freescale microcontroller xs128AD of analog-to-digital conversion code)

三相电流表源程序 基于CS5460a 485通讯 遵循mudbus协议 测试成功(Three-phase ammeter source based CS5460a 485 communications follow mudbus protocol test )

本方案是基于富士通高可靠性单片机开发的锂电池电动螺丝刀，采用直流无刷电机作为核心，配合方波驱动以及闭环控制技术，实现电动工具的可靠运行。 技术参数 1）采用日本富士通MCU，性能稳定，抗干扰强，高可靠性； 2）直流18V输入（可兼容不同锂电池10V—36V）； 3）三相霍尔直流无刷电机驱动，转速高达25000转/分； 4）采用德国英飞凌高性能MOS/IGBT，驱动功率高达800W； 5）高亮LED照明，工作时点亮，不工作时自动熄灭； 6）采用智能控制技术实现待机（不工作时）功耗为 0 消耗； 7）通过软件实现软启动，启动时间可调整，瞬间（1S）达最高速； 8）具有过流保护、堵转保护、过压欠压保护； 9）带速度设置按键、正反转按键、调速开关； (The program is based on the Fujitsu MCU development of high reliability lithium battery electric screwdriver, brushless DC motor as the core, with the square wave drive and closed-loop control technology, power tools for reliable operation.)

此程序可实现长度为8位，周期为255的m序列，此序列可当做伪随机信号发生器，模拟信道噪声。(This procedure can achieve the length of 8 bits, the m sequence of 255 cycles, the sequence can be used as a pseudorandom signal generator, analog channel noise.)

stm32芯片--用GPIO口模拟I2C驱动MPU6050陀螺仪(Stm32 chip- using GPIO port simulation I2C driver MPU6050 gyroscope)

本总体方案完成国标GB20600-2006数字电视地面广播传输系统基带部分功能。 输入数据码流经过扰码器（随机化）、前向纠错编码（FEC），然后进行比特流到符号流的星座映射，再进行交织后形成基本数据块，基本数据块与系统信息组合（复用）后并经过帧体数据处理形成帧体，帧体与相应的帧头（PN序列）复接为信号帧（组帧），经过基带后处理转换为输出信号（8MHz带宽内）。该信号经变频转换为射频信号（UHF和VHF频段范围内）。用C程序设计了图形交互界面，可以在界面上直接设置调制参数。(The overall program completion GB GB20600-2006 digital terrestrial television broadcasting transmission systems baseband function. The input data stream through the scrambler (randomization), forward error correction (the FEC), then the symbol constellation mapping bitstream to the stream, and then after forming the basic block interleaving, the basic data block and information combined system ( multiplexing) after data processing and after the frame body forms a frame body, frame body with a corresponding header (PN sequence) multiplexed signal frame (framing), after post-processing baseband signal is converted to an output (internal 8MHz bandwidth). The signal is downconverted to a radio frequency signal (in the VHF and UHF frequency range). C program designed graphical interface, you can set modulation parameters directly on the screen.)

超再生遥控-遥控步进电机正反转AB的程序(Superregeneration Remote- remote control stepper motor program AB)

红外遥控解码，基于51单片机的例程，简单实用，我在学习单片机的时候用到的(Infrared remote control decoding, based on 51 MCU routine, simple and practical, I used the time to learn microcontroller)