MINISTM32-SPI

基于51单片机的 红外+LCD+继电器C程序显示 实现的功能较多，比较适合初学的人。(Based on 51 single-chip infrared+LCD+ relay C program display of more functions, more suitable for beginners person.)

电池保护板检测，检测电池的电压、电流和温度代码。 (Battery protection board testing, test the battery voltage, current and temperature code.)

电协开发板 C51单片机程序，用于实现单片机的流水灯输出(Electric Association C51 microcontroller development board procedures for the realization of single-chip light water output)

32位单精度浮点数的乘加运算的C编程，感兴趣的可以看一下(Single-precision floating-point multiply-add operation of the C programming, interested can look at)

万年历开发 时间Calendar Development - Time(Calendar Development- Time)

AT89C51控制步进电机，实现正反转加减速，驱动芯片是ULN2803.(AT89C51 control the stepper motor to achieve reversing acceleration and deceleration, the driver chip is the ULN2803.)

说明：  红外接收相关资料，很值得一看，是初学者学习的绝好资料(Infrared receiver information, it is worth a visit, is an excellent information for beginners to learn)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)

打孔机主要用于在制造印刷线路板流程中的打孔作业。本问题旨在提高某类打孔机的生产效能。 打孔机的生产效能主要取决于以下几方面：（1）单个过孔的钻孔作业时间，这是由生(this is a new suan fa ofaa)

说明：  程序为基于Zigbee无线通信的点对多点无线通信源程序。ZigBee堆栈是在IEEE 802.15.4标准基础上建立的，定义了协议的MAC和PHY层。CC2430为基于51核心的高性能芯片。程序的编译平台为chipcon公司的IAR..(program of CC2430 )