shangweiji

基于单片机开发的无线识别装置系统中使用的应答器程序代码(The development of microcontroller-based system using wireless identification device transponder code)

交通灯数码管显示4*4键盘修改时间~带仿真图和源代码 模块化编写(Traffic lights digital display 4* 4 keypad to change the time ~ with simulation diagram and source code modular writing)

Infi-90读写测试，在安装有COPOSER的计算机上可以运行，采集ABB DCS的控制逻辑块上的数据。(Infi- 90, speaking, reading and writing test, the installation of COPOSER can run on a computer, the data on the acquisition of ABB DCS control logic block.)

xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1－启动与停止步进电机运行 K2－设定步进电机运行圈数 （1-20圈） K3－设定步进电机转动方向 K4－设定步进电机运行速度 步进电机的转速控制分16档，数字越小，转速越快。 7.5度步进电机；周期7.5×4=30度，电机转动一圈需12个周期 资源：p1.0-p1.3接反向器74ls14，输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口按键：lcd1602插入实验仪(xl Series Singlechip Experiment LCD1602 demo program shows the direction of stepper motor speed controller circle shows the number of adjustable LCD1602 direction stepper motor controller lap speed of a few adjustable K1-start and stop the stepper motor running K2-setting step motor running a few laps (1-20 laps) K3-set stepper motor rotation direction of K4-setting speed of stepper motor stepper motor speed control minutes 16 stalls, the number of smaller, faster the speed. 7.5 degree stepper motor cycle of 7.5 × 4 = 30 degrees, rotating electric lap 12 cycles required resources: p1.0-p1.3 then reverse browser 74ls14, followed by stepper motor output p3.7 then provide a small speaker key tone, p1.4-p1.7 port access keys: lcd1602 insert Tester)

CodeWarrior仿真与调试要点，CodeWarrior仿真与调试要点，CodeWarrior仿真与调试要点(CodeWarrior simulation and debugging points, CodeWarrior simulation and debugging points, CodeWarrior point emulation and debugging)

有关AVR的单片机adc的源代码，阐述详尽，便于使用(ADC OF AVR )

实现对气体流量表的基于音速喷嘴的自动检定(testing for the gas flow meters based on stangdard acoustic nozzles)

说明：  手消毒器应用，已经用于产品。是先喷消毒液；再进行手烘干。非常好奥(Hand disinfection applications, has been used for products. Is to spray disinfectant further hand drying. Very good Austrian)

一个数字梯形，选择k条路线，每条路线从第一层的某个数开始，每次进入下一层到达左下或者右下的数字，直到最后一层为止。每条路线不能经过相同的路径，但是可以经过相同的数字节点。 输出一个整数，表示能得到的最大的k条路径经过的数字之和(A digital ladder, the K route, each route the first layer of a number, each time to enter the next layer to reach the left or right next to the number, until the final layer. Each route can not pass through the same path, but can pass through the same number of nodes. Output an integer representing the sum of the number of the largest K paths that can be obtained)

说明：  power electronic machine model