ADC1_TriggerConversion

测试程序ATMEGA8LED的灯亮和灯灭(Test ATMEGA8LED lights turn on and off)

伺服电机控制系统，02年开始积累，效果好，速度快，PI控制，经典控制，fuzzy PID，自适应控制，速度位置控制等等，欢迎大家参考。(Servo motor control system, in 2002 began to accumulate, effective, fast, PI control, classical control, fuzzy PID, adaptive control, speed position control, etc., we welcome the reference.)

能够快速读取电子海图，还有简单的显示功能(ENC )

直流发电机的调速程序，使用的是STC12C5A的单片机，采用PWM技术来调节他的速度，简单便捷。(DC generator speed control program use is microcontroller of STC12C5A, and PWM technology to adjust his speed, simple and convenient.)

永磁同步电机直接转矩控制系统，模糊PID控制程序，包含M文件(Permanent magnet synchronous motor direct torque control system)

一款电厂巡检软件，很简单的C++处理程序，适合初学者使用，C++(A plant inspection software, very simple C++ handler for beginners, C++)

步进电机28BYJ48型四相八拍电机，电压为DC5V—DC12V。当对步进电机施加一系列连续不断的控制脉冲时，它可以连续不断地转动。每一个脉冲信号对应步进电机的某一相或两相绕组的通电状态改变一次，也就对应转子转过一定的角度（一个步距角）。当通电状态的改变完成一个循环时，转子转过一个齿距。四相步进电机可以在不同的通电方式下运行，常见的通电方式有单（单相绕组通电）四拍（A-B-C-D-A。。。），双（双相绕组通电）四拍（AB-BC-CD-DA-AB-。。。），八拍（A-AB-B-BC-C-CD-D-DA-A。。。）(Stepping Motor 28BYJ48 four-phase eight-phase motor, the voltage DC5V-DC12V. When a series of continuous control pulses are applied to the stepper motor, it can be continuously rotated. Each pulse signal corresponds to the stepper motor of a phase or two-phase winding power state change once, also corresponds to the rotor through a certain angle (a step angle). When the change in the power-on state completes one cycle, the rotor turns one pitch. Four-phase stepper motors can be operated in different power-up modes. The common power-up modes are: single-phase winding power (ABCDA ...), double (dual-phase winding)-DA-AB-...), eight beats (A-AB-B-BC-C-CD-)

PWM调光 1、学习目的：利用定时器产生PWM，了解原理和使用方法 2、硬件要求：LED灯 定时器 3、试验现象：LED灯由亮到灭，由灭到亮逐步变化，也就是调光现象(PWM dimming, learning objectives: the use of the timer to generate PWM understand the principles and use hardware requirements: LED lamp timer test phenomenon: LED lights from bright to off, gradually changes from off to bright, that is, adjusted optical phenomena)

99秒马表，在Proteus设计两个数码管动态显示及一个键盘SP。在ucos下结合keil完成开始时，显示“00”，第1次按下SP后就开始计时。 第2次按SP后，计时停止。第3次按SP后，计时归零。 (99 seconds stopwatch, two in the Proteus design dynamic digital tube display and a keyboard SP. Keil in combination ucos completed under the beginning of the show " 00" , 1st timer after pressing the SP. 2nd by SP, the time to stop. The 3rd by the SP, the time zero.)

SD Specifications_Ver3.01