tekradius

利用单片机（STC89C52）为核心结合机械按键、数码管以及稳压器件等电子元器件组装了一个数字时钟，可以实现精准的计时以及修改等功能；(The combination of mechanical buttons, digital tube, and electronic regulator device the microcontroller (STC89C52) as the core components assembled a digital clock, and can achieve precise timing and modify functions )

说明：  OCM12864参考程序_ 挺好的 适合做参考程序(_ OCM12864 reference to procedures for the very good reference procedures)

单片机驱动的OLED显示屏，单色绿光。C语言(Single-chip-driven OLED display, monochrome green. C language)

说明：  下面的程序利用友元函数求两点间的距离。请你将有关的程序补充完整，并总结为什么这里要用友元函数来求两点间的距离。(using friend to get the result.)

STM32F407信号发生器输入一个正弦波，AD采样，DA输出，系统频率应该是输入的波形的频率的10倍以上保证输出波形的完整性，系统的输出频率可以使用示波器测试出。(Stm32f407 signal generator input a sine wave, AD sampling, Da output and system frequency should is 10 times the frequency of the input waveform to guarantee that the above output waveform of integrity, the output frequency of the system can use oscilloscope to test out. )

CC2530 步进电机控制实验。一个简单的例程(CC2530 stepping motor control experiment)

C8051F060 自带高速AD进行数据采集 可达100兆采样率 并切缓存与片外ram 并把采集数据通过串口发送给PC ( Data Acquisition example for C8051F060 Description: This example illustrates the use of ADC1 and the DMA to acquire and store data. It is intended for use with the C8051F060 target board in the development kit. // This code measures a signal at the AIN0 input with the 16-bit SAR ADC0. // The data is sampled at a rate of 100kHz. ADC output data is transferred to XDATA memory space using the DMA. // // With the EMIF configured for off-chip XRAM access (on the upper ports), this code moves the ADC data to the C8051F060TB target boards s SRAM device. // Once data acquisition is complete, the code then prompts the user to press the P3.7 // button on the target board when ready to receive the data via the UART0 serial port. The TB features an RS-232 transceiver and connector, so the data can be transferred // to a PC via its serial port. // The code is set to acquire up to 32768 samples (for 64kbytes of data). The SRAM device - can accommodate up to 128kbytes, )

底层调用了PCSC的通信库Winscard，可用于PC上读卡器与智能卡的通信(It calls the underlying communication library Winscard PC can be used on a PC to communicate with the smart card reader)

此程序为毕业设计之防火防盗报警器具有MQ2烟雾报警，DS18B20温度报警，红外传感器感应人体红外，超声波感应人得进入，加上1602液晶显示等功能，同时具有蜂鸣器及LED报警(This procedure for the graduation of the fire alarm system design has MQ2 smoke alarm, DS18B20 temperature alarm, human infrared sensor infrared sensor, ultrasonic sensor people allowed to enter, plus 1602 LCD function, but also has a buzzer and LED alarm)

AGV小车上位机控制程序,通过TCP/IP协议来进行数据的传送(AGV car PC control procedures, through the TCP/IP protocols for data transmission)