M16-NRF2401

基于示波法的电子血压计程序，包括脉搏测量。控制器采用STM32F103C8T6。包含数据核心算法程序。( Based oscillography electronic sphygmomanometer procedures, including pulse measurements. Controller uses STM32F103C8T6. It contains data core algorithm program.)

modbus通信程序,可用组态软件的驱动程序开发(modbus communication program, available configuration software driver development)

Seekers导引头模型仿真C++源码；内含Seeker仿真模块、导引头电机环节、导引头PID环节等。(Seekers seeker model simulation C++ source containing Seeker simulation module, motor aspects seeker seeker PID link and so on.)

包含了C8051的基本例程，如流水灯，IO口控制，蜂鸣器，串口通信等(C8051MCU example programs)

I2C与mens传感器通信应用ch341-I2C-labview(I2C and mens tongxin)

xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1－启动与停止步进电机运行 K2－设定步进电机运行圈数 （1-20圈） K3－设定步进电机转动方向 K4－设定步进电机运行速度 步进电机的转速控制分16档，数字越小，转速越快。 7.5度步进电机；周期7.5×4=30度，电机转动一圈需12个周期 资源：p1.0-p1.3接反向器74ls14，输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口按键：lcd1602插入实验仪(xl Series Singlechip Experiment LCD1602 demo program shows the direction of stepper motor speed controller circle shows the number of adjustable LCD1602 direction stepper motor controller lap speed of a few adjustable K1-start and stop the stepper motor running K2-setting step motor running a few laps (1-20 laps) K3-set stepper motor rotation direction of K4-setting speed of stepper motor stepper motor speed control minutes 16 stalls, the number of smaller, faster the speed. 7.5 degree stepper motor cycle of 7.5 × 4 = 30 degrees, rotating electric lap 12 cycles required resources: p1.0-p1.3 then reverse browser 74ls14, followed by stepper motor output p3.7 then provide a small speaker key tone, p1.4-p1.7 port access keys: lcd1602 insert Tester)

MSP430F169单片机矩阵键盘扫描程序，用一位共阳数码管显示(MSP430F169 microcontroller matrix keyboard scanning procedures, using a common anode LED display)

说明：  CRC循环的代码，可以用，很详细，欢迎下载(CRC cyclic code can be used, in great detail, are welcome to download)

单片机学习，光敏和热敏电阻实验中的DA-AD转换程序(MCU learning, photosensitive and thermistor experiment DA-AD conversion program)

交流电动机的矢量控制（Transvector Contrl）理论，从理论上解决了交流电动机转矩的高性能控制问题。其基本思想是在普通的三相交流电动机上设法模拟直流电动机转矩控制的规律，在磁场定向坐标上，将电流矢量分解成产生磁通的励磁电流分量 和产生转矩的转矩电流分量 ，并使两分量互相垂直，彼此独立，然后分别进行调节。这样，交流电动机的转矩控制，从原理和特性上就与直流电动机相似了。因此，矢量控制的关键仍是对电流矢量的幅值和空间位置的控制。(AC motor vector control (Transvector Contrl) theory, control theory to solve the problem of high-performance AC motor torque. The basic idea is to try to simulate the DC motor torque control law in the ordinary three-phase AC electric motor in field-oriented coordinates, the current vector decomposed to produce the excitation current component of the magnetic flux generating a torque current component and torque, and two components perpendicular to each other, independently of each other, and then were adjusted. Thus, AC motor torque control, the principle and characteristics of the DC motor on and similar. Therefore, the key vector control is still the amplitude and spatial position of the current vector control.)