5110

由于太阳能充电系统多在户外，为了方便研究太阳能充电控制系统对蓄电池的充电情况，本文使用GPRS无线传输技术，设计了一套太阳能充电系统蓄电池的充电电压电流远程实时监测系统。系统的硬件部分由电压电流检测电路、单片机STC89C52RC、GPRS模块SIM300以及相应的外围电路构成，下位机软件由C语言编写并与硬件部分构成系统下位机部份，实现了对充电电压电流的信息采集以及数据的无线数传。上位机在LabVIEW2010环境下编写，具备友好的人机交互界面，实现了数据的远程接收、实时显示、数据库管理、报表生成和打印等功能。经过系统测试系统实现了对电压电流的远程监测。(As the solar charging system more outdoors, in order to facilitate the study of solar charge control system for charging the battery case, we use GPRS wireless transmission technology, we designed a solar charging system battery charge voltage and current remote monitoring system. The hardware part of the system by the voltage and current detecting circuit, microcontroller STC89C52RC, GPRS module SIM300 and corresponding peripheral circuits, lower computer software written in C language and hardware parts lower position machine part of the system, the realization of the charging voltage and current information collection and wireless data transmission of data. PC at LabVIEW2010 prepared environment, with friendly interactive interface, realize the remote receiving data, real-time display, management, report generation and printing. After the system test system enables remote monitoring of voltage and current.)

使用方法： 程序设置了ENC28J60的IP为192.168.0.15，模块通电后与电脑的网口用网线连接起来， 设置电脑的本地IP为192.168.0.**（**自定），网关为192.168.0.15,其他默认，配置 成功后便可以arp或ping模块。 打开浏览器，在地址里输入http://192.168.0.15/123456可打开开发板简单网页，页 面上通过按键来控制开发板LED的亮灭。(Use: setup the ENC28J60 of IP to 192.168.0.15, the module is powered on the computer' s Ethernet port using a cable connection up to set the computer' s local IP 192.168.0.** (** Custom), the gateway 192.168.0.15, default configuration is successful, it will make arp or ping module. Open the browser, enter the address http://192.168.0.15/123456 to open the development board simple web pages, and page keys to control the development board LED light off.)

msp430f149 adc-rs232 数据传输(msp430f149 adc-rs232 data transfering)

MQ-7烟雾模块 DHT11模块 430单片机驱动 数字量 非模拟量 1602显示(MQ-7 DHT11 430F149 1602)

小车沿着黑带前进，这事往年一个竞赛题目的程序，对大家有帮助。(The car along the black belt, it past a contest questions purpose program, are helpful to you. )

使用C51单片机开发的电梯源程序，单片机开发源程序(Use elevator source C51 MCU development, microcontroller development source)

at89c2051利用74ls164 驱动 共阳极数码管(74ls164 driver to use a total of at89c2051 digital tube anode)

TI公司的ADS1299是8路低噪音同时取样的24位delta-sigma ADC,并内置了可编程增益放大器(PGA),基准电压和振荡器,集成了脑电图(EEG)所需的通用特性.器件具有非常低的输入参考噪音:1.0 μVPP (70-Hz BW),没路的功耗5mW,输入偏置电流300pA,数据速率250SPS到16kSPS,C1.0 μVPP (70-Hz BW),CMMR为-110dB,可编程增益为1, 2, 4, 6, 8, 12或24,单极或双极电源工作,主要用在医疗仪器如EEG和ECG,听觉诱发电位(EAP),脑电双频谱指数(BIS),睡眠研究监测等,高精度多路信号采集.(The ADS1299 is a low-noise, multichannel, simultaneous-sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converter (ADC) with a built-in programmable gain amplifier (PGA), internal reference, and an onboard oscillator. The ADS1299 incorporates all commonly-required features for electroencephalogram (EEG) applications.)

计算太阳位置，通过公式！用单片机编译程序！(Calculate the position of the sun through the formula! Microcontroller compiler!)

本程序是基于msp430单片机的uart驱动程序(This procedure is based on MSP430 microcontroller UART driver)