8255input-outputexpeimental-

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)

msp430f149三相逆变电源源代码，可以输出6路spwm信号(msp430f149 spwm)

包含了C8051的基本例程，如流水灯，IO口控制，蜂鸣器，串口通信等(C8051MCU example programs)

2.4G研发详细文档，对没有无线基础的同学非常有帮助！(2.4G development with the document, very helpful to students based on no wireless! )

实现HDLC链路层的校验模块程序，在ads和mipchipc30上都调试成功。(HDLC link-layer implementation of the calibration module procedures, mipchipc30 in ads and on the success of all debugging.)

通过PWM定时器延迟一秒，实现一个LED灯的明灭。实验中观察I/O口的值对LED灯的明灭的控制，学习I/O口的输入输出方式和设置，了解PWM的配置方式(Through the PWM timer to delay a second, the realization of a LED lamp at. I/O values for LED lamp light control experiment, learning I/O port input and output method and setting, understanding of PWM configuration methods)

在定时器控制下反复的裁减一幅图像和改变其大小(timer under the control of the repeated cuts an image and change its size)

PCB设计接地指导书,指导pcb设计及人员更好的设计PC版(PCB design ground, guide the pcb design and make better PC version of the design)

直流斩波变化的仿真和一些参考文献 可以学习一下(The simulation of dc chopper change and some references can learn )

可以用的飞思卡尔智能车测试程序，非常不错的(Freescale smart car test procedures can be used, very good)