xunhuanzhouqijiance

非线性拟合,用于非线性拟合时，可以用这个现成的代码，很发方便！(Nonlinear fitting for nonlinear fitting, you can use the existing code, it is made ​ ​ easy!)

计算机网络数据链路选择性重传实验。 　　设计一个滑动窗口协议，在仿真环境下编程实现有噪音信道环境下两站点之间无差错双工通信。信道模型为8000bps 全双工卫星信道，信道传播时延270毫秒，信道误码率为，信道提供字节流传输服务，网络层分组长度固定为256字节。(Computer network data link selective retransmission experiment. Design of a sliding window protocol in simulation programming environment there is no error duplex communication channel between the noisy environment the two sites. Channel model is 8000bps full-duplex satellite channel, the channel propagation delay 270 ms, channel bit error rate, channel provides a byte stream transmission services, network layer packet length is fixed at 256 bytes.)

说明：  实现图像的分割。改程序是在matlab环境下运行的，程序中用到了k-means算法，实现的结果很不错(This is the program of image segmentation based on the following work: S. Chen, L. Cao, J. Liu, and X. Tang, "Image Segmentation by MAP-ML Estimations", submitted to IEEE Transactions on Image Processing. Note that this program was only tested on 32-bit PCs installed with Windows XP or Windows Server 2003. Since the K-means algorithm used in this program is from Matlab Statistics Toolbox, the program runs slower than when a faster K-means algorithm is used which can be obtained at http://vision.ucsd.edu/~pdollar/toolbox/doc/. The program was tested using Matlab R14 and the image processing Matlab Toolbox is required to run it.)

自动生成地震波,在无试验数据的情况下自动产生与实际相符的地震波(product seismic wave)

此为机器人模糊控制中的模糊控制规则，在模糊控制中加入此模糊控制规则，可得到仿真(This is the robot fuzzy control fuzzy control rules, fuzzy control fuzzy control rules by adding this can be obtained simulation)

数学建模论文 题为试卷评阅 进行分析建模求解编程(Thesis papers on mathematical modeling to analyze Review programming model for solving)

用七元线形天线阵（ULA） 已知：信号中心波长为2,天线阵元的间距为1米,快拍数为2000，空中有四个 源信号,假设它们的频率：0.015, 0.05, 0.02, 0.035 四个源信号的方向分别为：pi/4 pi/3 pi/6 3pi/4 求： 1）在不加入噪声的情况下,画出传统波束形成法、Bartlett波束 形成法、Capon波束形成法的空间谱图； 2）在加入高斯白噪声的情况下,假设信噪比为10dB，画出传统波束 形成法、Bartlett波束形成法、Capon波束形成法的空间谱图。(7-element linear antenna array (ULA) Known: the signal center wavelength is 2, the antenna element spacing of 1 m, the number of snapshots for 2000, the air there are four Source signal, assuming that their frequency: 0.015, 0.05, 0.02, 0.035 The direction of the four source signals: pi/4 pi/3 pi/6 3pi/4 Requirements: 1) not to join the noise, to draw the traditional beam-forming method, Bartlett, beam Formation method, Capon beamforming method of the space spectrum 2) by adding Gaussian white noise, assuming that the SNR is 10dB, to draw the traditional beam Formation method, Bartlett, beamforming, Capon beamforming method of the space spectrum.)

基于多尺度的小波边缘检测的matlab的代码，含有去噪算法(Edge detection based on wavelet multiscale matlab code, containing de-noising algorithm)

说明：  CT三维重建程序代码，正常运行，适合研究这方面的初学者学习借鉴(CT three-dimensional reconstruction program code, normal operation, suitable for beginners to learn from this aspect)

考虑两个参数的一维三角概率模型,用贝叶斯方法对其进行估计，了解贝叶斯估计方法.(Consider the two parameters of one-dimensional triangular probability model, using Bayesian methods to estimate their understand Bayesian methods.)