80C51

89c52的串口通信的演示 (89c52 serial communication demonstration)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)

基于m16的温度控制系统，主要用ds18b20(failed to translate)

仿真过程中，将改进算法那与经典算法进行比较，通过对仿真数据如系统时延、系统丢包概率以及系统吞吐量的比较分析，评估改进算法的正确性和性能。(Simulation process, the improved algorithm that compares with the classical algorithm, through the simulation data system latency, packet loss probability of the system as well as a comparative analysis system throughput, improved assessment of the correctness and performance of the algorithm.)

在单片机上运行的简单的颜色跟踪算法,中文注释(Running on the microcontroller simple color tracking algorithm, Chinese Notes)

本文讲述了细分驱动技术的原理，重点介绍了细分驱动控制系统的设计方法，设计了一套传统细分驱动系统的设计方案，在此基础上，本文进一步介绍了L297、L298两块芯片，采用这两块芯片构成步进电机的驱动电路，应用DAC0832实现D/A转换，采用精简指令集单片机AVR作为脉冲产生器，对步进电机的工作过程进行控制，最终组成电机细分数可选的驱动控制系统。(failed to translate)

同三维万能采集卡系列开发SDK包,包含例程等! (With three-dimensional universal capture card series development SDK package includes routines, etc.!)

STC12C5204AD单片机控制单个二极管闪烁源代码，二极管由138译码器使能，另一端单片机IO口控制，采用延时程序，是单片机初学者很好的学习源代码(STC12C5204AD flash microcontroller source code to control a single diode, diode 138 by the decoding is enabled, the other end of the single-chip IO port control, using the delay procedure is a very good chip for beginners to learn the source code)

IIc应用，AT24C512初始化，清零，存储，读取多字节存入 写入多字节(IIc applications, initialization, clear, store, read, write more bytes into a multi-byte)

对矩阵键盘的程序编写，详细地讲述了如何扫描键盘的输入！(The matrix keyboard programming, detailed tells the story of how to scan the keyboard input!)