登录
首页 » matlab » DSP_MATLAB

DSP_MATLAB

于 2010-12-02 发布 文件大小:1KB
0 299
下载积分: 1 下载次数: 21

代码说明:

  关于数字信号处理的MATLAB例程,包括随机信号产生,线性调频Z变换,卷积(MATLAB on digital signal processing routines, including the random signal generation, chirp Z transform, convolution)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 11111
    MATLAB图像处理实现直线识别(拟合角平分线)(MATLAB image processing line identification (fitting Angle bisector) )
    2014-12-12 14:42:02下载
    积分:1
  • Partial-differential-equations-student-solutions-
    Partial differential equations student solutions manual
    2014-02-19 10:15:28下载
    积分:1
  • kalman
    kalman滤波matlab程序,利用双点差分外推法取初值,并多次求平均值(kalman filter matlab procedures, the use of two-point difference extrapolation to take initial and repeated averaging)
    2014-05-10 10:33:07下载
    积分:1
  • MATLAB_filter
    基于MATLAB的数字滤波,包含源程序及说明(MATLAB-based digital filtering, including source and description)
    2008-03-29 17:02:40下载
    积分:1
  • MATLAB
    利用MATLAB 实现数据读入,对水准网平差进行处理,及数据输出等功能!(Using matlab implementing a data into the net, the standard of the poor and data processing, output and functional! )
    2010-10-24 16:23:52下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • Kalman
    KAlman 滤波 平滑估值等 很全,还有多维高斯白噪声产生方法(kalman gassion filter)
    2009-02-12 23:46:23下载
    积分:1
  • PlaneFrameModel
    有限元模型的建立,这些程序构成了有限元模型,用PlaneFrameModel来指定(PlaneFrameModel)
    2009-12-14 20:57:59下载
    积分:1
  • 2Tx1Rx
    用matlab仿真的空时分组码2根发射天线一根接收天线(Matlab simulation using space-time block codes two antennas a receiving antenna)
    2010-01-19 16:28:01下载
    积分:1
  • PID-source-code
    关于PID控制的一些例程,与薛定宇老师的反馈控制配套,与大家一起分享(PID control on a number of routines, and Xue Dingyu teacher feedback control facilities, and shared with)
    2011-04-27 08:23:37下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载