butterworth

说明：  利用MATLAB编写的一些图形处理方面的程序，非常适用。(Prepared to use some of MATLAB graphics processing procedures, is very applicable.)

说明：  chorus音频效果仿真处理，可从麦克风录入(chorus audio simulation, from the microphone input)

本书附带光盘中包括了全书所有实例对应的MATLAB的M文件。所有代码按照章节存放在各个文件夹下，如“第4章 插值”文件夹下存放了本书第4章所有的算法程序代码，对于算法的程序代码，在光盘中存为同函数名的M文件，例如，Language.m表示求已知数据点的拉格朗日插值多项式的程序，依此类推。(Book with CD-ROM includes all instances of the book corresponds to the MATLAB M-file. All code is stored in accordance with chapters in every folder, such as " Chapter 4 interpolation" folder stored under chapter 4 of the algorithm all the code for the algorithm of the program code, stored on CD-ROM for the same function name in the M file, for example, Language.m known data points that seek Lagrange polynomial interpolation procedures, and so on.)

Matlab2012最新教程(代码直接复制调试)(The latest Matlab2012 tutorial)

SINS和GPS组合导航，内包含程序，需要的数据，以及运行后得分析图等等。非常好，可以直接拿来用。(SINS and GPS navigation, and contains the program, the data needed, and post-run analysis chart and so on. Very good, can be directly used.)

说明：  实现了rip ospf bgp等路由协议的开源代码。(achieved a rip bgp OSPF routing protocol, such as open-source code.)

this tutorial will help beginners in the radar image processing. The programs are arranged in form of the chapters. all the best.

利用ccs环境、MATLAB环境、DSP（TMS320F2812)、被测对象和Agilient网络分析仪E5071B，构建一个自动测量系统。 相信大部分人都知道基于NI公司的GPIB总线，可以实现自动测量，但NI公司的方案实在太昂贵，采用MATLAB能够大大降低成本。matlab与ccs之间基于RTDX协议进行数据交换，同时matlab基于TCP/IP协议与E5071B之间通信，源码说明如下： （1）RTDX_ok目录：matlab7.0代码，包含了一个用GUI实现的界面和相关的具体代码，特别是在其中实现了SCPI语言来对仪器进行控制。 （2）TMS320F2812目录：包含ccs下的c代码，如果没有做过RTDX的应用，相信这个对你很有启发。(Use ccs environment, MATLAB environment, DSP (TMS320F2812), the measured object and Agilient network analyzer E5071B, construct an automatic measurement system. I believe that most people are aware NI' s GPIB-based bus, you can realize automatic measurement, but NI' s program is too expensive, the use of MATLAB can greatly reduce costs. ccs between matlab and RTDX protocol-based data exchange, while matlab based on TCP/IP protocol and communication between the E5071B, the source described as follows: (1) RTDX_ok directory: matlab7.0 code, contains a GUI implementation with the interface and specific code, especially in one of implementation of the SCPI language to control the apparatus. (2) TMS320F2812 directory: contains ccs of c code, if not done RTDX application, then I think it was very instructive for you.)

MODEM芯片内部寄存器地址，对每个寄存器进行操作，操作的数值很多，一个一个罗列下来。(MODEM chip register address for each register to operation, the operation of the values many, listing one by one down.)

其意见书是根据亚历山大Gramfort的“MATLAB的网状到PDF与三维交互对象“。他的计划将允许网数字转换成3D PDF格式。然而，他的代码只允许一个层进行转换，并不会启用的透明度。 本意见书不创建最终的PDF。它产生的U3D文件，然后可以使用到PDF的Adobe Acrobat Pro文件插入。本文件还允许多层网格，以创建，并为每个层的透明度指定。 此代码包含一个函数（installGoogleArchive.m），它会自动下载并安装所需的中间数据格式转换（IDTF）进入最后的通用3D（U3D）文件的二进制文件。此代码还只包括转换器的Windows版本。(his submission is based on Alexandre Gramfort s "matlab-mesh-to-pdf-with-3d-interactive-object". His program allows meshes to be converted into 3D PDF figures. However, his code only allows a single layer to be converted, and does not enable transparency. The present submission does not create the final PDF. It generates the U3D file which can then be inserted into a PDF file using Adobe Acrobat Pro. This submission also allows multilayer meshes to be created, and for the transparency of each layer to be specified. This code includes a function (installGoogleArchive.m) which will automatically download and install binaries required to convert the intermediate data format (IDTF) file into the final Universal 3D (U3D) file. This code also only includes the windows version of the converter.)