1

读写器与射频卡通信的设计采用RC522射频读写芯片与射频卡进行通信，符合ISO14443规范协议；硬件系统设计中主要有AVR单片机主控模块、电源模块、存储模块、外部时钟模块、LCD模块；软件系统设计采用C语言，遵循模块化和结构化编程模式，设计了射频卡操作程序、软关机与自动关机程序、LCD显示、串行Flash存储器、外部时钟等外部设备驱动程序。所设计的手持式读写器具备对MF1 S50、S70射频卡的读写、实时状态显示、系统在线升级以及关机等功能。(This handset can process the data offline or online, reading and writing from 10 cm far. This handset is low-power, miniature, modular design and so on. This article includes: the communication design between RF card and Reader, hardware system design and software systems design. The communication design between RF card and Reader used to RC522 RF chip control RF cards, in line with ISO14443 standard protocol Hardware system design mainly include AVR microcontroller control modules, power modules, memory modules, external clock modules, LCD modules Software system designed with C programming language, and follow the modular structure of the programming model, and has the RF card operation procedures, soft shutdown and automatic shutdown procedures, LCD display, serial Flash memory, an external clock, and other external device driver Procedures. The handset readers has the MF1 S50, S70 RF card reader function, real-time status display function, the system online update function and so)

全自动可遥控旗帜升降系统以AVR单片机为核心，由PWM对电机进行变频调速，高精度光电编码器测速，闭环式电路控制。能够利用按键输入相应的指令控制旗帜的升降，还可以实现在特定位置停留的功能。利用LCD可以显示旗帜的实时高度和相应的控制命令，用LED指示旗帜是否处于半旗状态，具有语音提示报警功能，并可利用无线模块实现遥控功能，准确均匀地实现旗帜的升降(Automatic landing system can be remote-controlled flag to AVR microcontroller core of the PWM VVVF motor, high-precision optical encoder gun, closed-loop control circuit. Enter the appropriate button to take advantage of the command control of the rise and fall of the flag, but also can stay in the function of a specific location. LCD can display the banner of the use of real-time high and the corresponding control command, the LED is directed at the flag half-mast, and alarm functions with voice prompts, and the use of wireless remote control function module, to achieve uniform and accurate take-off and landing flag)

modbus通信程序,可用组态软件的驱动程序开发(modbus communication program, available configuration software driver development)

用的是时钟芯片pcf8583，可以正常显示时间,并带有有Proteus仿真，非常形象！，已通过测试。 (Is clock chip pcf8583, can properly display the time, and with Proteus simulation, the very image of , Has been tested.)

STM32F1与FPGA通过SPI进行通信，我上传的是32部分的程序，已经通过串口测试成功。此程序可拓展为和单片机，DSP通过SPI进行通信(STM32F1 and FPGA communication through the SPI, I uploaded the 32 part of the procedure has been successfully tested through the serial port. This program can be extended to and single-chip, DSP communication through the SPI)

AD0809的功能启动，描述了如何启动AD0809的数模转换功能，并且在旁边加油注释(The AD0809 s function is activated, and describes how to start the AD0809 digital to analog conversion function, and next to the fuel comment)

实现对气体流量表的基于音速喷嘴的自动检定(testing for the gas flow meters based on stangdard acoustic nozzles)

以c51单片机为核心，利用1760芯片进行语音报时，51单片机控制(With c51 microcontroller core, the use of 1760 chip for voice timekeeping, 51 MCU control)

设计的电机驱动控制系统的主要功能有①控制电机的正转、反转；②为电机设计控制速度，有5m/s、10m/s、15m/s三个等级；③给电机设定转动的位移，让电机按照设定的位移移动；④1602液晶上显示电机的位移和速度；⑤利用4*4键盘数字输入控制电机的速度、按键C和D控制正反转、按键B控制三个档位的速度。(Using SCM software and hardware systems to achieve precision stage displacement, velocity through three or four phase stepper motors (motors meet the acceleration and deceleration characteristics), control the direction, location. Completion of the control circuit board hardware, including CPU, power amplifier, buttons, LED display. Software can be implemented in C.)

基于周立功CAN的上位机软件，可以实现对CAN的打开，波特率设置，滤波设置，消息发送，消息接受等等。亲测可用。完全可以作为二次开发的资料。(Based ZLG CAN PC software can be achieved on the open CAN baud rate settings, filter settings, the message is sent, the message to accept more. Pro-test available. Can be used as secondary development information.)