本程序运行于C8051F330，功能为接收遥控器发出的红外信号，然后等待上位机通过I2C总线来读取。IR数据接收完毕后，不再采集新的IR数据，一直等待上位机将数...

使用主模式I2C向CAT24WC02写入10字节数据，然后读出校验，若校验通过则BEE发声，否则不断BEE。 基于ADS1.2-use the main mode I2C CAT24WC02 to write 10 bytes of data, and then read out the check, if the check is through BEE audible, constantly BEE. Based on ADS1.2

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]

S3C44B0扩展16C554串口，包括原理图和源码 原来上传过源码，看到很多人下载，考虑到下载者阅读方便，所以这次增加了原理图。-16C554 serial S3C44B0 expansion, including schematics and source code uploaded the original source, to see a lot of people to download, taking into account that those who download the ease of reading, so the increase in schematics.

MSP430F149 LT-1B开发板相关的范例程序，不错的。-MSP430F149 LT-1B development board related example programs are good.

开发环境:ADS 1.2 目标平台:ARM:S3C44B0 显示屏:tft4.3" 480*272(24Bit) GUI:UCGUI324 项目功能:实现UCGUI在ARM7和彩屏LCD上成功移植 Seloo@tom.com 2008-10-12-Development Environment: ADS 1.2 target platforms: ARM: S3C44B0 display: tft4.3

利用51单片机实现sle4442的读写，可以使用-51 Singlechip sle4442 realize the use of reading and writing, you can use

51单片机直接驱动液晶显示，里面有两个程序！-51 Single-chip Direct Drive Liquid Crystal Display, which has two procedures!

美国美信公司温度DS18B20的驱动程序-USA and the United States believed the company DS18B20 temperature driver

汇编源代码，红外应用源程序集，主要 是关于红外探测技术的。-compilation of source code, source Set infrared applications, mainly for infrared detection technology.

利用C8051F单片机控制的铣床模型（直线圆弧插补算法）-C8051F MCU using milling machine model (straight line circular interpolation algorithm)