这是LCD1602与msp430之间的通信,其实可以直接从51移植过来,但是一定要在硬件加上拉电阻,要不然是不通不过的,我说的是你用的是5V的LCD...

SD2403A时钟芯片在STC单片机下的源程序 此芯片价格便宜，性能稳定！-SD2403A clock chip in the source code under the STC in this single-chip chip prices, performance and stability!

用MEGA128做的串口服务器,包括原理图,源代码,TCPIP开发资料,接口包括RS232,RS485,RJ45-MEGA128 to do with the serial server, including schematics, source code, TCPIP development information, interface, including RS232, RS485, RJ45

这是一个为51系列单片机开发的4*4键盘驱动程序。该驱动程序包括2个文件，使用时将C文件关联入工程，在调用文件前包含H文件即可。本键盘驱动程序具有两个接口函数提供两种扫描方式（阻塞和非阻塞），可以任意定制返回键值，具有防抖动处理，具体使用方法可以参见注释。（本程序在Keil C51开发环境中测试成功，并经过多次实践应用）。-This is a series of 51 MCU development of the 4* 4 keyboard driver. The drive included two documents, the use of paper will be linked into C, the call of documents containing H documents. The keyboard driver has two interface functions provide two scan mode (blocking and non-blocking), it will return to arbitrary custom keys with innovative and handling, the use of specific methods can be found in Notes. (This procedure Keil C51 development environment to test successful, and after several practice application).

八路电压表C程序 使用AT89C52单片机，12MHZ晶振，P0口读入AD值，P2口作AD控制，用共阳LED数码管 P1口输出段码，P3口扫描，最高位指示通道（0-7）。-Eight-way voltage meter C program using AT89C52 single-chip, 12MHZ crystal, P0 I read into the AD value, P2 I make AD control, with a total of P1 Yang LED digital tube output above code, P3 port scan, the maximum channel bit instructions (0-7).

EEPROM 24c04其根本是，先往24C02中写数据，然后，读出数据，在数码管中显示，这样直观明了，详细说明，请看程序中注解-EEPROM 24c04 其根本是，先往24C02中写数据，然后，读出数据，在数码管中显示，这样直观明了，详细说明，请看程序中注解

freescale单片机串行通讯程序,数据包方式，支持数据发送正常检验,并可使用命令实现对片机FLASH的读、写和擦除功能。-Freescale MCU serial communications, data packets, sends the data to support normal testing and can be used to achieve an order-of-FLASH read, write and erase functions.

C8051F9XX单片机SMBUS示例程序-Singlechip C8051F9XX SMbus sample programs

c8051f340的usb程序，经过自己的从头开始写到通讯完好。可以直接使用-c8051f340 the usb procedures, through their written communication in good condition to start from scratch. Direct access to

mega16,驱动开发板上的独立按键，按下不同的键，数码管显示0-3四个数字-MEGA16 KEY

72段LCD驱动器SD0418的测试程序-72 LCD drive SD0418 test procedures