关于如何提高速度的单片机，包括硬件和软件就怎么做了…

c51primer

基于C51及SL811读写U盘的源程序，开发文档资料,芯片数据手册,测试命令及测试工具,电路原理图,请参C51_SL811_ModeDisk_manual-Based on the C51 and SL811 source disk to read and write U, the development of documentation, the chip data sheet, test orders and test tools, circuit schematic diagram, please refer to C51_SL811_ModeDisk_manual

DS18B20温度采集和输出显示程序，用汇编语言实现-DS18B20 temperature acquisition and display program output, using assembly language to achieve

单一灯的左移右移分别接在单片机的P1.0－P1.7接口上，输出“0”时，发光二极管亮，开始时P1.0→P1.1→P1.2→P1.3→┅→P1.7→P1.6→┅→P1.0亮，重复循环-A single light, respectively, shifted to right then left at P1.0-P1.7 microcontroller interface, the output " 0" when the bright light-emitting diode, the beginning of P1.0 → P1.1 → P1.2 → P1. 3 → ┅ → P1.7 → P1.6 → ┅ → P1.0 Liang, repeat cycle

ARM7 lpc2148通过DS18B20温度采集并通过1602显示-ARM7 lpc2148 through DS18B20 temperature acquisition and through 1602 show

freescale hc12_C32 例程-Freescale hc12_C32 routines

MSP430 149的4×4键盘扫描程序（中断方式），以及JM12864M的液晶驱动程序，谢谢指教-MSP430 149 of 4 × 4 keyboard scan program (interrupt mode), as well as LCD driver JM12864M Thank you advice

这是VB编程RS232串口（COM口）控制的D/A(数模转换)转换板的上位机演示程序。通过电脑串口（或其他具有串口的单片机、PLC、DSP）发个简单的可视ASCII指令，便可以方便地控制8个数模转换通道输出设定的电压值。比如,电脑串口输出字符串"C2V2660"到本控制板,则控制板将控制2号通道输出2.66V电压；电脑串口输出字符串"C6V3060"到本控制板,则控制板将控制6号通道输出3.06V电压.指令非常简单，完全不需了解复杂的硬件及时序控制。-This is a VB programming RS232 serial port (COM port) control D/A (digital-analog conversion) conversion board host computer demonstration program. Via the computer serial port (or other serial port of the microcontroller, PLC, DSP) made a simple visual ASCII commands, they can easily control the number of eight-channel DAC output set voltage. For example, the computer serial output string " C2V2660" to this control panel, then the control board will control 2-channel output 2.66V voltage computer serial output string " C6V3060" to this control panel, then the control board will control the 6 channel output voltage is 3.06V. instruction is very simple, completely without understanding of complex hardware and timing control.

经典的DSP的C程序和汇编程序, 非常好!-Classic DSP-C procedures and compilation of procedures, very good!

系统采用SONIX单片机作为控制核心，通过按键可以记录当前数据并保存到EEPROM中，也可以读出来-NO