单片机音频信号处理软件1。

24位高精度AD：AD7710的中文资料-24 high-accuracy AD: AD7710 Chinese information

DAC0800产生幅度可调正弦波的程序,调试通过了哦-Generated sine wave amplitude adjustable DAC0800 procedures, debugging through the oh

基于51单片机的U盘型MP3设计（含C语言程序，原理图）-51 MCU-based U-disk-based MP3 design (including C language program, schematic diagram)

DS1302读写一体化C51源程序-DS1302 source code reader integration C51

51方面的一些代码-51 some of the code

芯片PCF8951共有四个A/D输入通道：AD0，AD1，AD2，AD3,分别与四个电位器(R1,R2,R3,R4)连接，用以调节电位器的输出电压。其中AD0通道既可测量电位器输出电压，也可用于测量从J1插座输入的外接电压，须用开关J2加以选择。J4插座提供由PCF8591输出的时钟方波信号。SAA1064驱动四个数码管显示一路AD转换后得到的数据。-PCF8951 chip, there are four A/D input channels: AD0, AD1, AD2, AD3, respectively, with four potentiometers (R1, R2, R3, R4) connected to regulate the output voltage potential. AD0 channel which can be measured potentiometer output voltage can also be used to measure the input from the J1 socket external voltage, to be used to select switch J2. J4 socket output from the PCF8591 clock square wave signal. SAA1064 drivers of four digital display along after AD conversion data.

基于320×240图形点阵液晶与51单片机的接口设计程序。采用C51编程制作。-Based on 320 × 240 dot-matrix graphic LCD interface with 51 single-chip design process. The use of C51 produced programming.

该程序通过调试，可以实现cc2420收发功能-The program through the debugger, you can realize CC2420 transceiver functions

完整的实现RS232与TCP/IP网络协议的转换-Realize the full RS232 and TCP/IP network protocol conversion

我用单片机8952和电压比较器339做了一个简单的电容容量测量表，参数大 致如下： 电容测量范围为1pF-9999.99uF，最小分辨力为1pF。分为5个量程，可以自 动切换量程，也可手动切换。 另外，有简单的频率计功能，能测量0-60MHz的数字信号频率（TTL电平）； 还可以产生几个单点频率的方波信号（比如1KHz）。 采用1602LCD作为显示器；4个按键控制；使用24C01保存当前设置值，不用 每次开机重新设置。可单5V供电，也可9V交流供电 -I used the single-chip 8952 and the voltage comparator 339 to do a simple capacitance measurement table, parameters are as follows: capacitance measurement range 1pF-9999.99uF, the minimum resolution for the 1pF. Divided into five ranges, you can automatically switch range can also be manually switched. In addition, a simple frequency meter function, capable of measuring 0-60MHz frequency digital signal (TTL level) can also lead to several single-point-frequency square-wave signal (for example, 1KHz). 1602LCD used as a monitor 4 button control use 24C01 to preserve the current settings, do not reset each boot. Can be a single 5V power supply, 9V AC power supply can also be