CY7C68013的GPIF burst源程序，主要示例GPIF BURST模式的使用，编译环境为KEIL...

交通灯,可控制行人过马路的时间,有protues图和c语言程序-Traffic lights, pedestrian crossing the road to that time, protues map and c language program

程序代码说明 P0401：用Prewitt算子检测图像的边缘 P0402：用不同σ值的LoG算子检测图像的边缘 P0403：用Canny算子检测图像的边缘 P0404：图像的阈值分割 P0405：用水线阈值法分割图像 P0406：对矩阵进行四叉树分解 P0407：将图像分为文字和非文字的两个类别 P0408：形态学梯度检测二值图像的边缘 P0409：形态学实例――从PCB图像中删除所有电流线，仅保留芯片对象-code P0401 Note : Prewitt operator to detect the edges in the image P0402 : different values of Getting operator to detect the edges in the image P0403 : Canny operator to detect the edges in the image P0404 : image thresholding segmentation P0405 : water line threshold method image segmentation P0406 : matrix Quadtree P0407 : images into text and non-text of the two categories P0408 : morphological gradient detection Binary Image Edge P0409 : morphology example-- Images from the PCB to remove all current lines, retaining only chip targets

P1.7～P1.0接发光二极管L8～L1，要求利用单片机内部定时器1，按方式1工作，每0.01秒T1溢出中断一次。要求编写程序模拟时序控制装置。开机第1秒钟L1、L3亮，第2秒钟L2、L4亮，第3秒钟L5、L7亮，第4秒钟L6、L8亮，第5秒钟L1、L3、L5、L7亮，第6秒钟L2、L4、L6、L8亮，第7秒钟8个发光二极管全亮，……一直循环下去。fosc=11.0592MHz-P1.7- P1.0 then LED L1 to L8, by using a timer internal microcontroller, a work by the way, every 0.01 seconds T1 interrupted an overflow. Simulation prepared timing control device. Boot 1 seconds L1, L3- liang, two seconds L2- L4, L5 three seconds, L7- liang, 4 seconds L6, L8-liang, 5 seconds L1, L2, L5, L7- liang, 6 seconds L2, L4, L6, L8- , 7 seconds 8-LED whole ... has been the cycle continues. 11.0592MHz fosc =

通过这个程序，你可以知道电话是怎样拨号，是怎样接通，怎样传输。-through this procedure, you know how to dial telephone is connected to what, how transmission.

51实现TCPIP协议原理图-51 TCPIP achieve agreement schematics

一个基于时钟芯片1302的单片机时钟。使用伟福的仿真器编译通过，同时写入单片机后的硬件电路也好使。-1302 based on the clock chip microcontroller clock. Wei-fu of the use of the compiler through the emulator, at the same time to write after the single-chip hardware circuitry or so.

VC++环境下的延时程序。sleep函数，还有delay函数。-VC++ Environment delay procedures. sleep function, as well as delay function.

LT_1B msp430开发板例子程序－TA_18

用C51语言开发，相当有趣，附详细文档及硬件电路图-with C51 language development, very interesting, with detailed documentation and hardware circuit

单片机C语言开发软件KEIL C，该软件上手容易，适宜于各个阶段的单片机爱好者-Singlechip C language development software KEIL C, the software easier to use, suitable for all stages of the single-chip lovers