算法支持的操作系统。非常适合移植的朋友。

sony servo

介绍了用CPLD辅助设计在嵌入系统中进行曲MPU复杂逻辑功能设计的总体方案，给出了通过对XC95144中复用控制寄存器进行配置以实现MPU复位逻辑和CPM协议切换的实现方案和设计要点。-Introduced aided design using CPLD in the embedded system, march MPU complex logic functional design of the overall program given by XC95144 the re-configured using control registers in order to achieve the MPU reset switch logic and CPM protocol implementations and design elements.

这是嵌入式开发进行AD数据采集时，通过软件对数据进行防干扰处理的方法汇总，希望对大家有帮助-This is the embedded data acquisition development of AD when the data through software deal with anti-interference method of aggregation, in the hope that everyone has to help

本程序采用dsp6713芯片，移植了ucos2操作系统，编程环境是ccs3.3。

一个U盘的文件系统源代码！！！C语言编写，推荐下载-a U disk file system source code! ! ! C language, to download!

430中精确延时方法，并已实际应用，效果良好，大大缩短了开发周期，这是实际应用资料。另外还有最好的按键程序。-precise delay, and has practical application, the results have been excellent, greatly reducing the development cycle, This is the practical application of information. Another best keys procedures.

nRF24E1作为 RF处理芯片，内带51处理器，其频段处于ISM频段，通信速度可以达到1M，可以进行跳频处理，在短距离高速度通信上有非常良好的功能。-nRF24E1 as an RF chip, which with 51 processors, the band at ISM band, communication speed can reach 1M, can Hopping, a short distance high-speed communications on a very good function.

STM32F4移植ucOS-ii工程文件。特点：1、尽量不改变STM32F4的库文件，尤其启动文件startup_stm32f4xx.s；2、移植系统所需改动是在工程文件的uCOS/Port文件夹；3、新建两个任务进行测试；4、硬件平台为ST的STM32F4-DISCOVERY评估板

L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是：工作电压高，最高工作电压可达46V；输出电流大，瞬间峰值电流可达3A，持续工作电流为2A；额定功率25W。内含两个H桥的高电压大电流全桥式驱动器，可以用来驱动直流电动机和步进电动机、继电器线圈等感性负载；采用标准逻辑电平信号控制；具有两个使能控制端，在不受输入信号影响的情况下允许或禁止器件工作有一个逻辑电源输入端，使内部逻辑电路部分在低电压下工作；可以外接检测电阻，将变化量反馈给控制电路。使用L298N芯片驱动电机，该芯片可以驱动一台两相步进电机或四相步进电机，也可以驱动两台直流电机。-L298N is produced by ST a high-voltage, high current motor driver chip. The chip uses 15-pin package. Main features are: high voltage, the maximum working voltage up to 46V output current, instantaneous peak current up to 3A, continuous operating current of 2A rated power of 25W. Contains two H-bridge high-voltage high-current full-bridge driver can be used to drive DC motors and stepper motors, relay coils and other inductive load using standard logic level signal control has two enable control terminal, input signal without affecting the case to permit or prohibit the device work a logic supply input, so that part of the internal logic circuits at low voltage work can be an external sense res

freescale ep100 PWM 程序，按程序中代码初始化即可启动使用PWM，代码已经经过调试。-freescale ep100 PWM process, according to the procedure in the initialization code to activate the use of PWM, the code had already been debugging.