Msp430的flash读写文件配置文件，(msp430f427芯片)

小日本用mega8 做的软件模拟USB 转232-Little Japan mega8 do with software simulation USB transfer 232

DS18B20温度测量，上下限温度设定测量（超出报警）-Upper and lower limits of temperature measurement (in excess of the police)

spi 翻译资料 7.2 SPI总线 SD卡信道由指令和数据位（起始位和结束位）组成，SPI信道由字节定向。 每一个指令或数据块由8位的字节和CS标志构成。类似SD卡协议, SPI通讯由 指令、响应和数据组成。全部的主机与SD卡之间的通信由主机控制。主机执行 每一跟CS标志为低的总线-spi Translation 7.2 SPI bus data channel from the SD card command and data bit (start bit and end bit) component, SPI channel directed by byte. Every command or data block from 8-bit bytes and CS constitute signs. SD card similar to the agreement, SPI communications from command, response and data components. All of the host and the communications between the SD card by the host control. Each host implementation with CS low marks for bus

lcd 与C51 的驱动程序 1、本实验箱采用的液晶显示屏内置控制器为SED1520，点阵为122x32，由两片SED1520组成，由E1、E2分别选通，控制显示屏的左右两半屏。-LCD C51 and a driver, the use of experimental boxes LCD screen embedded controller for SED1520, to 122x32 dot matrix, composed of two SED1520, E1, E2 respectively strobe control screens around two semi-screen.

拷拷贝到你的Keil安装目录下的c51in文件夹中。 工程文件中需设置一下: project->Option for Target Target1 选Debug页 左侧最下面 Dialog Dll 一般是DP51.DLL，不用修改 Parameter 中是 -P51 在其后加入 -dledkey 即该行看起来应该是这样的： -p51 -dledkey 保存即可 进入调试后，点击：Peripherals，其中多出一个“键盘LED实验仿真板”选择该项即可。-emboss your copy of the Keil installation directory under the decoder bin folder. The project document to be provided as follows : project-gt; Option for Target Target1 election Debug bottom of the left page is generally Dialog Dll DP51.DLL, need not be amended Parameter is- P51 add after-dledkey that the bank should look like this :-p51-can be preserved into dledkey to debug and click : Peripherals, in which more than a "keyboard LED simulation board," which can be chosen.

端口控制发光二极管亮灭。 【硬件连接】通过SPCE061A的1位I/O端口（本例中使用IOA15端口），经一限流电阻后接一个发光二极管至地-Port control to eliminate bright light-emitting diodes. [] Through SPCE061A hardware connection of an I/O port (in this example, the use of IOA15 port), with a current limiting resistor followed by a light-emitting diodes to land

源码PB做的一个全新的触摸屏系统，请大家试用-PB-source to do an entirely new touch screen system, U.S. trial

利用51单片机对u盘进行读写操作，其中用到的usb芯片是sl811master。-use 51 to u-SCM write, which to use the USB chip is sl811master.

单片机用于控制NFR2401的程序，可实现ZIGBEE功能-This is a mcu programmar to control NFR2401

使用IAR编译器移植ucOS到S3C44B0X上 -Use IAR compiler to S3C44B0X on transplantation uCOS