包含protue 7.2 仿真文件及汇编语言源代码。主要是一个4X4的键盘以及一个LCD显示显示屏。键盘输入显示在LCD上。...

可以红外遥控的渐亮白炙灯(PIC12F629），喜欢的请下载，这又是一个实用又有趣的小制作。-Infrared remote control can be gradually brightening light Sunburn (PIC12F629), like the download, this is a practical and interesting production.

IAR例子，里面是一个完整的串口异步通讯例子。-IAR examples, which is a complete example of serial asynchronous communication.

20ma的电流环通信回路仍应用于一些远程通信的场合，本文为其实现过程。-20ma current loop

PIC单片机PIC18F系列的CAN通讯事例程序，下载者可通过该程序了解PIC中CAN通讯原理。-PIC18F family of PIC microcontroller examples of CAN communication process, download the program who can understand the principle of PIC in the CAN communication.

对初学者会有用。主要针对于西门子STEP7组态编程的实践程序。软件平台《step7v5.3》-Be useful for beginners. The main target in the configuration of Siemens STEP7 programming practice procedure. Software platform

利用脉冲控制伺服电机运转，伺服电机频率通过改变定时器初值来控制-The use of pulsed operation of servo motor control, servo motors by changing the timer frequency to control the initial value

PIC18单片机与LCD1602的C语言程序，主要LCD几个控制管脚的定义。-PIC18 MCU and LCD1602 the C language program, the main LCD control pins of several definitions.

ds1631温度传感器程序，I2C总线的，好用-ds1631 temperature sensor procedures, I2C bus, easy to use

此源码利用单片机实现以太网接口，实现方法简单，实用。-use of this source MCU Ethernet interface method is simple and practical.

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov