I2C总线的一个实例,有原理图的设计,和程序的设计,可直接用在项目开发中,节约开发时间,提高效率....

TI公司的MSP430F1611单片机的液晶显示程序-TI

简单的跑马灯程序 经过测试可以成功运行在单片机上-Bomadeng simple procedures can be tested successfully on the run in SCM

一个完善的单片机tcpip实现,包括http/tftp/pop3/smtp,开发环境是富士通的16位单片机-a perfect realization of SCM TCPIP, including http/tftp/pop3/smtp, development environment is Fujitsu"s 16-bit MCU

LT_1B msp430开发板例子程序－T1

可以实现在PC与CAN总线的连接。采用的89C51和SJA1000芯片的接法。里面包括原程序的电路斩-Can be achieved in the PC and CAN bus connection. Used 89C51 and SJA1000 chip connection. Procedures which include the original circuit Tsam

l298调 速 程 序 常规的接法是这样的，EnableA接PWM信号，Input1输入正反控制信号， Input2是Input1经过反相以后的信号。L298的电平是与TTL电路相兼容的，一般是超过2.5V就为高电平。假如Input1为高电平时电机正转，那么低电平时就是反转，PWM信号控制电机的转速。 _________________ -l298 procedures conventional speed connection that is the case, EnableA then PWM signal, Input1 input positive and negative control signals, Input2 is Input1 through after RP signal. L298 level is compatible with TTL circuits, and is generally more than 2.5V for the high. If Input1 is high when the motor is transferred, then that is when low-level inversion, PWM signal to control motor speed. _________________

CC2420 提供了发送确认帧的固件，使能AUTOACK 将使得硬件可以自动生成确认帧。-CC2420 provides a frame to send to confirm the firmware so that it can AUTOACK will allow the hardware can automatically generate confirmation frame.

DS18B20温度测量，上下限温度设定测量（超出报警）-Upper and lower limits of temperature measurement (in excess of the police)

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]

完全实用化的020 SMBUS程序（与时钟PCF8563通信-Entirely of 020 SMBUS utility program (with the clock PCF8563 communication