矢量变频器控制源程序

80C52单片机上用C语言实现的双机红外通信程序，可以替代遥控器遥控长虹电视机，具有一定的学习性功能。-80C52 single-chip using C language to achieve the two-plane infrared communication program, an alternative to Changhong TV remote control, the study has certain features.

STC单片机的AD功能测试。测试中通过P3口的LED指示AD值。-STC microcontroller AD functional tests. Testing of the LED through the P3 port direction AD value.

该源代码为单片机的加油机课程设计源代码，需要课程设计报告的，再找我。-The source code for the MCU tanker curriculum design source code, the need for curriculum design report, I find.

44780字符液晶屏驱动演示程序总线方式-44,780 Character LCD Driver Bus Demonstration Program

12864LCD单片机程序,包括写入中文字符以及输出数字等-12864LCD single-chip process

单片机用T1中断在IO口P1.0输出乐曲(在P1.0口与VCC间接一喇叭即可听到) 1.由于输出的是方波，比较难听:-)你也可以将波形细分用DA输出正弦波 2.由于T1频繁中断，任何其他中断发生都会是乐曲打顿，只适合试验 3.优化音符编码：一个字节中包含节拍、音符、升降调，可区分数据和命令 -Single-chip microcomputer used in the IO port T1 interrupt output music P1.0 (P1.0 port with VCC in the indirect one can hear the speaker) 1. As the output is a square wave, more bluntly :-) You can also fine-waveform DA output sine wave with sub-2. Due to the frequent interruption of T1, any other interruption occurs Dayton will be playing music, is only suitable for test 3. optimized coding notes: A byte contains rhythms, notes, take-off and landing tune can distinguish between data and command

MSP430 F149的单片机 ADC驱动程序，便于相应计时器的操作-MSP430 F149 microcontroller ADC drivers, easy operation of the corresponding timer

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

时钟芯片12c887非常实用，现奉上它的程序仅供参考。-12c887 chip clock is very useful, now offering its program is for reference only.

lcd common driver with mcu