51 libraries, a number of cases, learning the basis of single

该源代码为单片机的火车时刻表课程设计源代码，需要课程设计报告的，再找我。-The source code for the MCU train schedules curriculum design source code, the need for curriculum design report, I find.

pic16f877a使用iic总线方式驱动低价温度芯片tc74，并液晶显示的一个程序，板上验证通过，可以直接使用，令附tc74中文资料-PIC16F877A using the IIC bus driven low temperature chip tc74, and liquid crystal display of a procedure to verify through the board, you can directly use, the attached information tc74 Chinese

用汇编程序编写的音乐控制 系统可以选择将近40首歌-procedures used to prepare a compilation of music control system can choose to nearly 40 songs

8*8点阵LED显示器的设计 并且有原程序和说明 很好的-8* 8 dot matrix LED displays and the design of the original procedure and a good note

利用单片机做的编码器输出值LED显示程序，用MAX7219驱动七段数码管，完成二‘十’十六进制的切换显示。-Does the use of single-chip encoder output LED display program with Seven-Segment LED Driver MAX7219, completion of the second

///*** *** *** * //一、程序说明： //1, 24LC02器件地址是1010000R/W. //2, 数组写入24LC02采取页写方式. //3, 数组code从24LC02读出时采取自由读方式. //4, 采用4.00M晶体。 //5，采用软件I2C。 //二、硬件连接： //1， SDA------->23 pin.(当然你可以任意选择脚位） //2, SCL------->18 Pin.(当然你可以任意选择脚位） //3， PORTB----->数码管的段输出 //4， RD4，RD5，RC6，RC7------->数码管的位输出(数码管为共阴极） -///*******************// A description of the procedures:// 1, 24LC02 device address is 1010000R/W.// 2, write an array to take 24LC02 page write mode.// 3, the array read out the code from the 24LC02 to take a free read.// 4, using 4.00M crystal.// 5, using software I2C.// Second, the hardware to connect:// 1, SDA-------> 23 pin. (Of course, you can choose to pin)// 2, SCL-------> 18 Pin. (Of course You can choose pin)// 3, PORTB-----> digital tube output segment// 4, RD4, RD5, RC6, RC7-------> digital pipe-bit output (digital tube for a total of cathode)

实现了有凌阳的外部中断进行技数，同时有2赫兹的内部定时器，以实现对外部频率的采集 -Sunplus has achieved the technology to a number of external interrupt, while Hertz has 2 internal timer in order to realize the acquisition of external frequency

430开发板PCB图，可直接开板，适用于初学者-430 development board PCB diagram, can be directly opened plate for beginners

12864中文资料，写有基本的使用指令-12864 Chinese data, writing the use of basic commands

LPC2103的第二个实验：流水灯+按键，用proteus7仿真，C语言代码，在Keil3中编译，文件内已有完整的工程和仿真图了。-The second experiment LPC2103: water lamp+ button, and proteus7 simulation, C language code, compiled at Keil3 in the paper that has a complete map of the engineering and simulation.