周立功ZLG7289 驱动原代码

ATMEL的AVR单片机库文件-the ATMEL AVR libraries

该书是单片机入门的一本好书，值得大家一看共同学习-The book is a single-chip entry of a good book, it is worth one U.S. study of common look

基于ATMEGA88 实现的漏电保护的程序源代码-ATMEGA88-based implementation of the program source code leakage protection

pic 单片机红外接收分析仪的资料，印制板部分，pdf文件格式，请参考使用-pic microcontroller infrared analyzer to receive the information, PCB, pdf format, please refer to the use of

可对多条串接的护栏管自动设置地址或单条设置地址-Can control multiple concatenation of the barrier is automatically set address or the address of a single set

SPI是一个环形总线结构，由ss（cs）、sck、sdi、sdo构成，其时序其实很简单，主要是在sck的控制下，两个双向移位寄存器进行数据交换。 假设下面的8位寄存器装的是待发送的数据10101010，上升沿发送、下降沿接收、高位先发送。 那么第一个上升沿来的时候 数据将会是sdo=1；寄存器=0101010x。下降沿到来的时候，sdi上的电平将所存到寄存器中去，那么这时寄存器=0101010sdi，这样在8个时钟脉冲以后，两个寄存器的内容互相交换一次。这样就完成里一个spi时序。 -SPI bus is a ring structure, by ss (cs), sck, sdi, sdo composition, its timing is actually very simple, mainly under the control of the sck and two bi-directional shift register for data exchange. Assuming the following 8-bit register is loaded to send the data to be 10,101,010, rising to send, receive falling edge, high first sent. Well, the first rising edge to the time data will be sdo = 1 register = 0101010x. Falling edge comes, sdi on the level will be stored to the register, then register at this time = 0101010sdi, so 8 clock pulse later, the contents of two registers to exchange time. This will be completed in a spi timing.

DAC1230与单片机的接口程序，已经调试通过-Interface with MCU DAC1230 procedures are debugging through

这是VB编程RS232串口（COM口）控制的D/A(数模转换)转换板的上位机演示程序。通过电脑串口（或其他具有串口的单片机、PLC、DSP）发个简单的可视ASCII指令，便可以方便地控制8个数模转换通道输出设定的电压值。比如,电脑串口输出字符串"C2V2660"到本控制板,则控制板将控制2号通道输出2.66V电压；电脑串口输出字符串"C6V3060"到本控制板,则控制板将控制6号通道输出3.06V电压.指令非常简单，完全不需了解复杂的硬件及时序控制。-This is a VB programming RS232 serial port (COM port) control D/A (digital-analog conversion) conversion board host computer demonstration program. Via the computer serial port (or other serial port of the microcontroller, PLC, DSP) made a simple visual ASCII commands, they can easily control the number of eight-channel DAC output set voltage. For example, the computer serial output string " C2V2660" to this control panel, then the control board will control 2-channel output 2.66V voltage computer serial output string " C6V3060" to this control panel, then the control board will control the 6 channel output voltage is 3.06V. instruction is very simple, completely without understanding of complex hardware and timing control.

本程序是7963液晶驱动,希望能对大家有所帮助-LCD Driver 7963, we hope to help

51系列单片机实验课程：串口 （通过计算机与试验箱相连，互相收发信息）-51 Series single-chip experimental curriculum: serial (through the computer and the chamber connected to each other to send and receive information)