x5045的c源程序，绝对使用通过，放心使用

此模块是我在以前公司做热风枪项目时设计的一个模块，用于实时显示当前温度，其精度可以达到1摄氏度，三位半液晶显示，界面美观，稍作改动也可用段码LED作为显示。 程序功能：10位A/D的温度采集（热电偶）；TN段码液晶驱动；温度补偿； 文件包括：所有C源程序；完整的项目文件包（基于MCU：HT46R23） PCB HT46R23 DATASHEET 三位半液晶片DATASHEET-This module is in my hot air gun to do before the company projects a module designed for real-time displays the current temperature, its accuracy can reach 1 degree Celsius, three semi-liquid crystal display, interface aesthetics, make a minor amendment to paragraph can also be used as a code LED display . Program features: 10-bit A/D Acquisition temperature (thermocouple) TN LCD driver code segment temperature compensation documents include: All C source code complete package of project documents (based on the MCU: HT46R23) PCB HT46R23 DATASHEET 3 semi-liquid crystal film DATASHEET

基于pic单片机的can 通信程序-pic based on SCM can Communication Program

pj working with a compiler

基于FREESCALE单片机9S08DZ60的LIN从节点的应用层源代码.LIN是通过UART串口来实现的.开发环境为CODEWARRIOR FOR HC08-Based on Freescale

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

在发一个PC机与51单片机通讯的程序，简单易懂。-In the hair of a PC machine with 51 single-chip communications procedures, easy-to-read.

本程序是一师兄给我的，用于液晶屏的滚动显示，给大家参考参考-this is a process, told it to me, for the rolling screen, to your information.

本人非常支持单片机设计DIY 在这里再次献出小弟的一点心意,下面是使用AT89S52驱动74HC4015,实现1选择8的数据通道切换器,可以在不8个通道出加上不同大小的电阻.可以用来单声道音量的大小控制. 下面作品图是小弟设计的廉价的 基于单片机的毕业设计 ,它还使用了无线接收发送模块,通过使用手上的遥控器能控制音量的大小,还加了一块HCF4052用于输入音道的选择,支持思路音频信号的输入,一路音频信号的输出: -I very much support the single-chip design DIY here again gave a little boy s mind is to use the following AT89S52 drive 74HC4015, to achieve a choice of 8 switches the data channel, you can not add the 8-channel resistance of different sizes. Can used to the size of mono volume control. The following work plan is designed小弟cheap graduation based on single-chip design, it uses the wireless receiver send module, through the use of the hands of the remote control can control the volume size, but also Add a piece of HCF4052 Road for the importation of sound choices, to support the idea of audio signal input, the output audio signal all the way:

LPC2378，共阴8位数码管显示测试程序，下载后可直接编译调试-LPC2378, a total of eight digital negative display testing procedures can be downloaded directly compile debug

采用ADC0809采集数据，并通过串口上传到上位机，采用C语言编写，简单易懂-using data acquisition, and through serial upload it to the PC using C language. easily understood