vb编写的上位机程序，可以实现的功能是单片机和上位机的通讯功能...

单片机用作通用红外遥控接收器的设计 PWM调制开关电源的研究 以电子电力学为核心 以整流技术为主-generic microcontroller for infrared remote control receiver design PWM switching power supply of electronic learning for power to the core technology-based rectifier

LT_1B msp430开发板例子程序－WDT1

C8051F020的头文件，主要是本单片机的硬件地址指向等。-C8051F020 the first document, is the MCU hardware addresses at the other.

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

(AD9958用ADuC845控制的keil源代码包,键盘和显示部分在另一个板上，通过串口发送指令和返回数据) 线路图在压缩包内-(AD9958 using ADuC845 control keil source code package, keyboard and display part in another on-board, through the serial port to send commands and return data) circuit diagram in the compression bag

PIC 单片机 CC2420 ZIGBEE C 源码-PIC Singlechip CC2420 ZIGBEE C source

usb开发工具周立功公司下载很好用的一个软件-development tools usb Ligong weeks to download a very good company with a software

51定时器初始值计算器(初学单片机的好工具)-51 timer starting value calculator (begins studies monolithic integrated circuit good tool)

电动车上面的控制器原理图，NEC主控芯片，现在最流行的方案，提供给大家-Electric vehicle controller schematic diagram above, NEC host chip, is now the most popular programs available to everyone

芯片PCF8951共有四个A/D输入通道：AD0，AD1，AD2，AD3,分别与四个电位器(R1,R2,R3,R4)连接，用以调节电位器的输出电压。其中AD0通道既可测量电位器输出电压，也可用于测量从J1插座输入的外接电压，须用开关J2加以选择。J4插座提供由PCF8591输出的时钟方波信号。SAA1064驱动四个数码管显示一路AD转换后得到的数据。-PCF8951 chip, there are four A/D input channels: AD0, AD1, AD2, AD3, respectively, with four potentiometers (R1, R2, R3, R4) connected to regulate the output voltage potential. AD0 channel which can be measured potentiometer output voltage can also be used to measure the input from the J1 socket external voltage, to be used to select switch J2. J4 socket output from the PCF8591 clock square wave signal. SAA1064 drivers of four digital display along after AD conversion data.