armlinux entry notes, very good, very strong

三星ARM2410boot代码，有一定的参考价值，在2410上BOOt成功过-Samsung ARM2410boot code, which is the reference value, in 2410, never succeeded in BOOt

Communication helper for stixxxx based systems. Usally used in firmware uploaders.

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch

行业表现领先的综合产品组合包括最新的32位LPC3000，LPC2000，LPC1000，LH7A，LH7和8位LPC900，LPC700和......XP LPC3130/3131180MHz的ARM926EJ-S CPU为核心，在一个芯片上的高速USB2.0 OTG，高达192KB SRAM，NAND闪存控制器，灵活的外部总线接口，4通道10位A/ D...

《新概念51单片机C语言教程:入门、提高、开发、拓展全攻略》书上例程代码

这是《ARM嵌入式应用开发技术白金手册》源代码，共含有9个程序-This is the

arm扩展can总线的驱动程序-arm can extend Bus Driver

附件為自己建立的stm32f107 ST晶片工程模板+UART2+gpio 已經實際上機測試過,可正常運行. 使用外部XTAL 8MHz, gpio設置最大50MHz, 可使用PL2303 接UART2到電腦進行測試 UART2傳輸

uboot for S3C2440 and nand flash boot 里面有对基于S3C2440 对nand flash的读写-uboot for S3C2440 and nand flash boot there S3C2440 based on the read and write nand flash

资源描述stm32的usb转串口程序代码，包括USART串口通信，DMA部分，中断函数部分等等，喜欢嵌入式设计的，正在学stm32的同学可以下载下来看看呦~