状态机制实现按键长按、短按、长按累加识别

NEC格式遥控接收代码：NEC IR implementation -NEC form remote control receive code: NEC IR implementation

代码ggggggKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKHHHHHHHHHHHHHHHHHHHFVFCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB

S3C2440A中IIC接口的基本操作编程，实现向AT24C02内部地址0x00~0xff依次写入数据，然后再读出并比较。-S3C2440A in the basic operation of IIC interface programming, to achieve the AT24C02 internal address 0x00 ~ 0xff followed by write data, and then read out and compare.

TMS320C6713固化程序到外部FLASH的flashburn程序及相关软件，以及FBTC的相关数据手册

arm7 plc2214

该文档讲述了stm32f10x系列中LIB库中的外设，很好的资料。-This document describes stm32f10x series in the peripheral LIB library, very good information.

针对传统电液比例控制系统的性能较差，本文提出了一种基于ARM和uC/OS-II的电液比例控制系统的设计，并详细介绍了以ARM内核微控制器LPC2292和电机驱动芯片LMD18200为核心的硬件电路，以及嵌入式操作系统μC/OS-II在ARM7上的实现。-Traditional electro-hydraulic proportional control system for poor performance, this paper presents an approach based on ARM and uC/OS-II of the electro-hydraulic proportional control system design and described in detail in order to ARM core LPC2292 microcontroller and motor driver chip LMD18200 at the core of the hardware circuit, as well as the embedded operating system μC/OS-II in the realization of ARM7.

s3c2410IIC程序，测试过可以用，可以读写AT24系列-s3c2410IIC procedures can be tested, you can read and write AT24 Series

JTAG的驱动程序，一般都是用在相对应的嵌入式ARM处理器上，这个事实用在LPC2210上面。-JTAG drivers are generally used in relation to the embedded ARM processor, with the fact that the LPC2210 above.

本程序是通过TMS320CS2047的DSP处理器,经过DSP内部事件管理器的配合,实现SPWM波输出!-This procedure is adopted TMS320CS2047 of DSP processors, DSP, after the internal event manager with the realization of SPWM wave output!