s3c2410 开发板的开发code 包括bootloader

ARM汇编指令集,全，容易理解，条理清晰-ARM instruction set to compile the whole, easy to understand, the clarity of

1. android-2.3.4-fs-20110518.tar.gz    Android 2.3系统的源代码包，总共1.1G多   2. android-kernel-2.6.36-20110517.tar.gz    Android系统所需要的Linux内核源代码包3. rootfs_android-20110518.tar.gz    已经编译好的Android 2.3目标文件系统压缩包，以更新日期作为尾缀4. u-boot-mini6410-20110405.tar.gz    完全开源的U-boot源代码包，支持USB一键下载，支持烧写WinCE(nk.nb0格式)，支持yaffs2，支持SD/NAND启动，    支持128M/256M DDR RAM，分别有不同的配置像，本光盘中所有的u-boot源代码包其实都是同一个文件，只是根    据不同的系统需要选择不同的配置项。见用户手册说明5. LEDDemo.rar   Android平台访问LED的示例应用程序

STC12C5410AD-是一款功能非常强大的且-兼容C51的单片机。本程序代码采用STC12C5410AD单片机驱动ICL7135双积分的高性能AD芯片。程序经几天调试通过。完全可用。-STC12C5410AD-is a very powerful and- C51-compatible microcontroller. The program code used STC12C5410AD single-chip dual-drive ICL7135 chip integration of high-performance AD. After a few days through the debugging process. Fully available.

ARM处理器软中断处理。a_swi.s文件是最开始处理的SWI句柄,用ARM汇编指令编写。c_swi.c文件是在执行a_swi.s文件之后调用执行的C语言SWI句柄。 -ARM processor soft interrupt handling. a_swi.s document is the beginning of the SWI handler deal with the preparation of ARM compilation directives. c_swi.c document is in the implementation of a_swi.s document called the C language implementation of SWI handler.

三个DS18b20测温点，三选二控制策略，485通信控制，自保持继电器控制，at89c2051控制-3 DS18b20 temperature measurement points, three selected two control strategies, 485 communication control, self-holding relay control, at89c2051 control

JTAG协议分析软件,配合周立功的LA1032逻辑分析仪使用,可以观察各种JTAG仿真器的通信过程.-JTAG protocol analysis software, with Zhou meritorious LA1032 logic analyzer use, can observe various JTAG Emulator for the communication process.

8253 烧写程序 8253 烧写程序-8253 procedures 8253 programmer programmer programmer procedures procedures 8253

this is RealTimeOS(uITRON) for hitachi H8 processor.-this is RealTimeOS (specification) for hitachi H8 processor.

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch

STM32的I2C例程，详细例程，能够使用的，下载完了要给点回复哦！-STM32