伺服马达控制的C51程序。 文件： sifu*.c sifu*.Uv2 sifu*.hex 等相关文件。...

这是利用51单片机来实现对cd-rom的控制并实现类似于mp3的功能!-This is the use of 51 single-chip microcomputer to realize on the cd-rom control and realize the function is similar to mp3!

nokia3310多功能温度计设计，显示介面随温度变化，可定时测量-Design of multi-function thermometer nokia3310, showing the interface with temperature change can be measured from time to time

ds18b20和1602液晶显示，能精确读取温度到小数点后两位。-LCD ds18b20 and 1602 can accurately read the temperature to two decimal places.

具体的硬件结构,大家可以看 WS 系列产品的原理图 * 利用AT89S51单片机来制作一个手动计数器，在AT89S51单片机的P3.3管脚接一个轻触开关， * 作为手动计数的按钮. 数码管驱动采用动态扫描方式用单片机的P0.0－P0.7驱动数码管的段码， * P1.3 控制个位数码管的共阳极公共端，P1.2 控制十位数码管的共阳极公共端 * 通过按一下P3.3按键,数码管做 1 的累加, 实现00~99的计数功能,当计到99时又从00开始. * 大家可自行修改程序,扩展到0000~9999的计数范围-Specific hardware architecture, we can look WS schematic family of products using AT89S51* Single-chip to produce a manual counter, in the P3.3 pin MCU AT89S51 by one touch switch,* as a manual count of button. nixie tube driven by dynamic scanning with MCU P0.0-P0.7 driver code segment digital tube,* P1.3 control bit digital tube anode of a total public client, P1.2 control of 10 digital total anode tube through public client* P3.3 click buttons, a digital pipe to do one of the cumulative, realize 00 ~ 99 count function, when the total to 99 from 00 the beginning of time.* everyone can modify the program, extended to 0000 range of ~ 9999 count

单片机C语言的上电初始化，这确实是个头疼的问题!-microcontroller on the C language-- initialization, it is indeed a headache!

电话拨号程序，开发环境：vc6.0,在win2k下调试通过。-Telephone dial-up procedures, development environment: vc6.0, in win2k adopted under the debugger.

水果分级，根据水果的大小自动算出经过的时间，然后控制机械部分动作实现分选-fruit grading, according to the size of fruit automatically calculate the elapsed time and then control the mechanical parts action to achieve separation

这是一个有关于单片机屏幕显示的的源代码。真的不很不错。-This is a single-chip has on-screen display of the source code. Really not very good.

点阵16x64 C51源程序+仿真 点阵16x64 C51源程序+仿真-16x64 C51 lattice source+ Simulation lattice 16x64 C51 source+ Simulation

内容：1、本程序用于测试4相步进电机常规驱动 2、需要用跳帽或者杜邦线把信号输出端和对应的步进电机信号输入端连接起来 3、速度不可以调节的过快，不然就没有力矩转动了 4、按s4（设置成独立按键模式）可以控制正反转 -Contents: 1, the procedure used to test the four-phase stepper motor-driven two conventional, need to jump cap or the signal output line of DuPont and the corresponding stepper motor signal input terminal connected three speed adjustment can not be too fast, Otherwise, there would be no moment of rotation of the four, according to s4 (set to form an independent key mode) can control the positive inversion