primitive code using VHDL prepared RAM, FIFO, ROM, and other commonly used stora...

1 前大灯可以随意打开和关闭； 2 当汽车左转弯的时候，前左转向灯闪烁，同时左后灯的3盏灯由右往左闪烁； 3 当汽车有转弯的时候，前右转向灯闪烁，同时右后灯的3盏灯有左往右闪烁； 4 当汽车减速或紧急刹车的时候，左后灯和右后等同时闪烁； 5 当汽车在左转弯的同时减速，则前左转向灯闪烁，左后灯的3盏灯由右往左闪烁，同时右后灯都点亮。 6 当汽车在左转弯的同时减速，则前右转向灯闪烁，右后灯的3盏灯有左往右闪烁，同时左后灯都点亮。 -a former headlamps can be opened and closed at will; 2 when the vehicle made a left turn when the former left to lights flickered. Left lights while the three lights flashing from right-go left; 3 when the vehicle is making a turn when a right turn to the former lights flickered. Right after the lights while the three lights are blinking right and left; 4 when the vehicle deceleration or when the emergency brake, Left and right after the lights blink, and so on; 5 when the vehicle made a left turn at the same time to slow down, and then to the left before the lights flickered. Left lights three lights flashing from right-go left, right after the lights are lit. 6 when a car made a left turn at the same time to slow down, and then right before the lights to flick

全自动洗衣机的控制器。 1.洗衣机的工作步骤为洗衣、漂洗和脱水三个过程，工作时间分别为：洗涤10秒，漂洗5秒，脱水5秒； 2.用一个按键实现洗衣程序的手动选择：A、单洗涤；B、单漂洗；C、单脱水；D、漂洗和脱水；E、洗涤、漂洗和脱水全过程； 3.用显示器件显示洗衣机的工作状态（洗衣、漂洗和脱水），并倒计时显示每个状态的工作时间，全部过程结束后，应提示使用者； 4.用一个按键实现暂停洗衣和继续洗衣的控制，暂停后继续洗衣应回到暂停之前保留的状态； (Automatic washing machine controller. 1 washing machine work steps for the laundry, rinsing and dehydration three processes, working hours are as follows: washed for 10 seconds, rinse for 5 seconds, dehydrated five seconds 2 with a button to manually select the program to achieve laundry: A, single-washing B, single rinse C, a single dehydration D, rinsing and dehydration E, washing, rinsing and dehydration the whole process 3 with a display device display the working status of washing machine (laundry, rinsing and dehydration), and each state countdown show working hours, after the whole process should prompt the user 4 laundry with a button to pause and continue control of laundry, laundry should be back after a pause pause before continuing to retain the state )

主要是基于FPGA(EP2C8Q208I8)下的SRAM驱动，SRAM型号为IS61LV25616，程序语言为Verilog,开发环境为quartusII 7.0,为一工程，可直接下载到FPGA中，含电路图(Mainly based on FPGA (EP2C8Q208I8) driving under the SRAM, SRAM model IS61LV25616, programming language for Verilog, a development environment for quartusII 7.0, for a project, can be downloaded directly to the FPGA, including circuit diagrams)

用Verilog实现FSK调制，调用IP核实现正弦余弦的调制-Verilog implementation using FSK modulation, called IP core to achieve the modulation sine cosine

vhdl code for carry lookahead addder

FPGA入门点亮一个LED灯，作为FPGA入门级程序(FPGA is)

基于FPGA的电子密码锁设计与实现，语言是VHDL语言，有注释(FPGA-based design and implementation of electronic locks, language is VHDL language, annotated)

快速傅立叶变换(FFT)作为时域和频域转换的基本运算，是数字谱分析的必要前提。传统的FFT使用软件或DSP实现，高速处理时实时性较难满足。FPGA是直接由硬件实现的，其内部结构规则简单，通常可以容纳很多相同的运算单元，因此FPGA在作指定运算时，速度会远远高于通用的DSP芯片。FFT运算结构相对比较简单和固定，适于用FPGA进行硬件实现，并且能兼顾速度及灵活性。本文介绍了一种通用的可以在FPGA上实现128点FFT变换的方法。设计复数乘法器为核心设计了FFT算法中的基-2蝶形运算单元，溢出控制单元和地址与逻辑控制模块等其它模块,并以这些模块和FPGA内部的双口RAM为基础组成了基-2FFT算法模块。 

本程序为捷变频信号的verilog源代码设计实现的仿真，并含有相应捷变频信号在MATLAB仿真的结果(The procedure for the Czech Republic converted signal verilog source code design and implementation of the simulation, and the Czech Republic frequency signal containing the corresponding simulation results in MATLAB)

基于System Generator的图像处理工程,多媒体处理FPGA实现的源码,图像边缘提取(System Generator based image processing engineering, multimedia processing FPGA implementation source code, image edge extraction)