登录
首页 » 算法 » 一维伽辽金型无网格法MATLAB程序 无网格方法采用基于点的近似,可以彻底或部分地消除网格,不需要网格的初始划分和重构,不仅可以保证计算的精度,而且可以大大...

一维伽辽金型无网格法MATLAB程序 无网格方法采用基于点的近似,可以彻底或部分地消除网格,不需要网格的初始划分和重构,不仅可以保证计算的精度,而且可以大大...

于 2022-06-18 发布 文件大小:1.69 kB
0 303
下载积分: 2 下载次数: 1

代码说明:

一维伽辽金型无网格法MATLAB程序 无网格方法采用基于点的近似,可以彻底或部分地消除网格,不需要网格的初始划分和重构,不仅可以保证计算的精度,而且可以大大减小计算的难度。然而,由于目前的无网格近似一般没有解析表达式,且大都基于伽辽金原理,因此计算量很大,要超出传统的有限元法;另外,无网格近似大都是拟合,因此对于位移边界的处理比较困难,多采用拉格朗日乘子法处理。-1维伽Galerkin-type meshless method MATLAB procedures meshless method based on the point of approximation, can be completely or partially eliminate the grid, the grid does not require the initial division and reconstruction, not only can guarantee the accuracy of the calculation, and can greatly reduce the difficulty of calculation. However, due to the current meshless approximation there is no analytic expression in general, and mostly based on the Galerkin principle, the calculation of a large volume, it is necessary to go beyond the traditional finite element method In addition, the meshless approximation are fitted, so displacement of the border more difficult to deal with, the use of Lagrange law.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 全梯度程序代码。数学,总梯度
    共梯度算法程序代码.数学上,共梯度法实求解特定线性系统的数值解的方法,其中那些矩阵为对称和正定。共轭梯度法是一个迭代方法,所以它适用于稀疏矩阵系统,因为这些系统对于象乔莱斯基分解这样的直接方法太大了。这种系统在数值求解偏微分方程时相当常见。 共梯度法也可以用于求解无约束优化问题。 -Total gradient algorithm program code. Mathematics, the total gradient method for solving a particular linear system is the numerical solution methods, including those for the symmetric and positive definite matrix. Conjugate gradient method is an iterative method, it applies to sparse matrix systems, because these systems such as the Cholesky decomposition of the direct method is too high. Such systems in the numerical solution of partial differential equations are quite common when. Total gradient method can also be used for solving unconstrained optimization problems.
    2022-08-06 23:27:29下载
    积分:1
  • 几个小排序
    几个小排序- Several slightly arrange
    2022-08-12 23:54:12下载
    积分:1
  • 51单片机仿三菱通信协议与工业人机界面通信
    51单片机仿三菱通信协议与工业人机界面通信.通信参数:端口RS232,波特率9600,偶校验,停止位1位
    2022-02-25 00:36:13下载
    积分:1
  • 基于VC单文档的B样条曲线实时仿真
    基于VC单文档的可视化B样条曲线绘制和仿真,可给定控制点,根据给定设定点自动绘制拟合后的B样条曲线,对学习B样条原理有很大帮助
    2022-02-28 12:29:48下载
    积分:1
  • 矩阵类,封装了一些有关矩阵的运
    矩阵类,封装了一些有关矩阵的运算-matrices, Packaging, a number of the matrix arithmetic
    2022-03-13 21:24:26下载
    积分:1
  • several independent firms for each and every line and every small units of one t...
    数独求解 每行和每列和每小格为1到9的数字,用程序求解的算发.-several independent firms for each and every line and every small units of one to nine the number of procedures for the count fat.
    2022-08-09 01:01:35下载
    积分:1
  • 拉格朗日插值的MATLAB
    MatLab的拉格朗日插值法-MatLab Lagrange interpolation
    2022-03-03 04:31:00下载
    积分:1
  • 混沌工具箱
    该工具箱是研究非线性时间序列混沌与分形的有力工具,能够计算非线性时间序列的动力学不变量,如关联维数,李亚普洛夫指数等指标。此外还包含相空间重构的过程中参数的估计方法。
    2022-04-22 23:13:45下载
    积分:1
  • LabVIEW一维数组转二维数组
    LabVIEW一维数组转二维数组,当一维数组元素不断增加时,将一维数组变为二维数组
    2022-03-25 03:40:57下载
    积分:1
  • 给定一块宽度为W的矩形板,矩形板的高度不受限制。现需要从板上分别切割出n个高度为hi,宽度为wi的矩形零件。切割的规则是零件的高度方向与矩形板的高度方向保持一致...
    给定一块宽度为W的矩形板,矩形板的高度不受限制。现需要从板上分别切割出n个高度为hi,宽度为wi的矩形零件。切割的规则是零件的高度方向与矩形板的高度方向保持一致。要求求出一种切割法使得所使用的矩形板的高度h最小.用递归及分治法解此问题-given a width of the rectangular plate W, the height of rectangular plate unrestricted. Board is required from the respective cut out n height of the hi, wi width of the rectangular parts. Cutting parts to the rules of the height of the rectangular plate with a high degree of consistent direction. Asked obtained a law made by cutting the use of the rectangular plate height h minimum. Using recursive and partition Solving this problem
    2022-10-31 04:20:03下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载