USBCDC

这个是LPC1788开发板的测试用例 都已经试过可以编译通过(This is the LPC1788 development board test cases have been compiled through)

uCOS+uCGUI-FSMC-2.8寸屏移植到STM32，在红牛板上演示成功。MDK编译工程(uCOS+ uCGUI-FSMC-2.8-inch screen transplanted to STM32, a successful demonstration in the Red Bull board. MDK compiler works)

说明：  实现瑞萨RL78系列单片机通过UART0显示ADC的值(Realize the display of ADC value by UART0 of rsal78 series single chip microcomputer)

说明：  用STM32F103C8T6的3组串口，分别连接cdebyte的无线收发模块，usar1接收到上位机命令，通过usart2向下转发，USart2接收到下位机数据，再由USart1向上转发， 实现中继转发功能。(Three groups of serial ports of stm32f103c8t6 are used to connect the wireless transceiver module of cdebyte. Usar1 receives the command from the upper computer, usar2 forwards downward, usar2 receives the data, and then usar1 forwards upward to realize the relay forwarding function.)

LPC1778的bootloader程序，通过U盘对设备进行操作！(LPC1778 the bootloader program, U disk to operate the equipment!)

STM32F103读写外部SRAM的程序，适用于神舟三号开发板(STM32F103 external SRAM read and write procedures for Shenzhou III development board)

stm32控制w5300 和sram实现网络数据传输(stm32 w5300 sram)

STM32F0XX教程+例程源码 教程目录： 工程篇：搭建KEIL-MDK开发平台及制作MDK工程文件模板.pdf 资料篇-NUCLEO-072RB开发板特性讲解及资料准备.pdf 初级教程篇：按键(中断方式)实现24C04存储器内容读写.pdf 初级教程篇：实现一个LED灯(软件延时 systick定时器).pdf 中级教程篇：利用SPI总线构建NUCLEO-072RB和NUCLEO-302RB双机处理系统.pdf 中级教程篇：利用定时器实现6路互补PWM波形输出.pdf 高级教程篇：基于Labview上位机界面的NUCLEO-072RB数据采集系统.pdf 例程目录： 1.ADC 2.BLDC 3.DEMO-工程模板 4.EEPROM 5.KEY(中断方式) 6.KEY-EEPROM 7.LED（systick定时） 8.LED(软件延时) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART(printf 查询方式接收) 14.UART(中断方式方式接收)(STM32F0XX tutorial + routine source code Directory of courses: Project: building KEIL-MDK development platform and making MDK project document template.Pdf Information sheet -NUCLEO-072RB development board characteristics and data preparation.Pdf Primary tutorial: key (interrupt mode) to achieve 24C04 memory content read and write.Pdf Junior tutorial: realizing a LED lamp (software delay systick timer).Pdf Intermediate tutorial: using SPI bus to build NUCLEO-072RB and NUCLEO-302RB dual processor system.Pdf Intermediate tutorial: using timer to realize 6 complementary PWM waveform output.Pdf Advanced tutorial: NUCLEO-072RB data acquisition system based on Labview host computer interface.Pdf Routine Directory: 1.ADC 2.BLDC 3.DEMO- engineering template 4.EEPROM 5.KEY (interrupt mode) 6.KEY-EEPROM 7.LED (systick timing) 8.LED (software delay) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART (printf query mode) 14.UART (interrupt mode receive))

STM32F103 TIMER操作例程,里面有各Timer设置和初始化例程(STM32F103 Timer Example )

基于STM32F103的BLM100模块RFID UHF读卡程序。能将读到卡的ID号显示在LCD屏上。(RFID UHF reader program module based on the STM32F103 BLM100. You can read the card ID number displayed on the LCD screen.)