nRF2401-

arm扩展can总线的驱动程序(arm can extend Bus Driver)

STM32F103 LTC4150电源管理 把电量和电量百分比放到stm32的内部flash中。(STM32F103 LTC4150 power management to power and the percentage of power into stm32 internal flash.)

STM32F0XX教程+例程源码 教程目录： 工程篇：搭建KEIL-MDK开发平台及制作MDK工程文件模板.pdf 资料篇-NUCLEO-072RB开发板特性讲解及资料准备.pdf 初级教程篇：按键(中断方式)实现24C04存储器内容读写.pdf 初级教程篇：实现一个LED灯(软件延时 systick定时器).pdf 中级教程篇：利用SPI总线构建NUCLEO-072RB和NUCLEO-302RB双机处理系统.pdf 中级教程篇：利用定时器实现6路互补PWM波形输出.pdf 高级教程篇：基于Labview上位机界面的NUCLEO-072RB数据采集系统.pdf 例程目录： 1.ADC 2.BLDC 3.DEMO-工程模板 4.EEPROM 5.KEY(中断方式) 6.KEY-EEPROM 7.LED（systick定时） 8.LED(软件延时) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART(printf 查询方式接收) 14.UART(中断方式方式接收)(STM32F0XX tutorial + routine source code Directory of courses: Project: building KEIL-MDK development platform and making MDK project document template.Pdf Information sheet -NUCLEO-072RB development board characteristics and data preparation.Pdf Primary tutorial: key (interrupt mode) to achieve 24C04 memory content read and write.Pdf Junior tutorial: realizing a LED lamp (software delay systick timer).Pdf Intermediate tutorial: using SPI bus to build NUCLEO-072RB and NUCLEO-302RB dual processor system.Pdf Intermediate tutorial: using timer to realize 6 complementary PWM waveform output.Pdf Advanced tutorial: NUCLEO-072RB data acquisition system based on Labview host computer interface.Pdf Routine Directory: 1.ADC 2.BLDC 3.DEMO- engineering template 4.EEPROM 5.KEY (interrupt mode) 6.KEY-EEPROM 7.LED (systick timing) 8.LED (software delay) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART (printf query mode) 14.UART (interrupt mode receive))

S3C2440上实现红外信号的接收的驱动程序。利用一个I/O口，不占用串口。已经在板子上实验通过了。(s3c2440 driver)

implementation of morse code using Nuvoton Development Board based on ARM microprocessor

LPC23XX 深入浅出的说明手册，书中含有大量的例程。(lpc23xx data sheep )

Dignostic test program for SMDK441f board chip peripellel. ADS1.2 compiler

Micrium官方移植的uc-OS III到 stm32f746平台，值得参考与借鉴。(This software package is ported to stm32f746 platform by Micrium.)

这是应用于 windows ce 4.2平台上串口接受的程序，我已经实践过，好用，也可以根据它修改出发送程序(This is used in windows ce 4.2 platform serial port to accept the procedure, I had already been put into practice, use can also be sent out according to its modified procedures)

vga demo fo stm32f103